(800) 853-2651
SHOP NOW

Recent content by j.c.n.

Yesterday's Tractor Forums
  1. J

    id 605 help ?

    i have a 605 cid. i need to know if pistons are std. or over. #in piston is 10a210 they are cast iron. thanks for any help.
  2. J

    carb no. for 101 Jr

    ralf if you can tell me what make carb or post a pic.i can help. jack.
  3. J

    430 clutch

    get a itt book and a gage. it will explane how to check the case-o-matic pressure.had one with the pump drive shaft broke off in bottom of trans housing. sounds like a case-o-matic,it has no clutch as you know.
  4. J

    Farmall 460 overheating Fast!!!!

    fyi. make sure you have a ihc thermostat. they have double use. when cold they heat up the block. when the motor is hot, they close off the block and push through the rad to cool. if this helps. i have seen this happen.
  5. J

    ralf from mich.

    right now i'm waiting on a 101 6 cyl. from an astate settlement. i have first chance. i would most likely sell the 101 jr.i had one about 1977.i tryed to find it , but the man i sold it to 25 years ago ,did'n know the man who bought it.
  6. J

    ralf from mich.

    i looked at my 101 jr. i don't have a carb. can't help right now/will check with a friend. jack.
  7. J

    39' 101 jr. row crop

    ralf from mich.i'll see if i can find some carb information on the carb i have and let you know jack.
  8. J

    39' 101 jr. row crop

    i have a 39' i traded for some ih parts. it needs a grill,motor don't run , tires,blast and paint.it has a brake peddle on each foot board. that's about all i know . is it worth restoring. any in put apreacated. jack thanks for your time.
  9. J

    560 turbo

    i have a td9-92 dozer motor, are the pistons the same as non turbo 282 in a 560 ?
  10. J

    560 turbo

    where 560 turbo dis. factory or dealer installed ?
  11. J

    earth master

    thanks gene, i'll pass it to my brother inlaw how's doing the work.
  12. J

    HD 800 into G1000?

    chris is the motor in your 1000 a gas or lp ? where are you and are you selling it off?
  13. J

    951-b cat

    to z656 if you want i can gave you a price. or if you have a tractor or equal to trade. e-mail or call 920-737-2221. measure pin center and number off link/number of links in one chain.thanks.
  14. J

    951-b cat

    the 941 are different i think a d-4 would be. ch eck pin spacing and link number.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top