(800) 853-2651
SHOP NOW

Recent content by jacka

Yesterday's Tractor Forums
  1. J

    Ferguson TED20 starter solenoid

    Hello John! Could you tell me how I adjustment new starting switch? Do I first put (adjustment) starting switch as far forward as possible? Or far back as possible?
  2. J

    Ferguson TED20 starter solenoid

    This is my new (only 100 starts) starter "solenoid". Good chinese quality. =)
  3. J

    Ferguson TED20 starter solenoid

    There is different models about new starter solenoids. Could someone tell which is the best new starter solenoid model? I heard that meny people have starter solenoid problems (new ones)...
  4. J

    TED20 - small oil leak near lower link arm

    Is it possible to stretch bolts 20 and 23 from the outside?
  5. J

    TED20 - small oil leak near lower link arm

    Picture 1. Oil leak is somewhere parts 21 and 22...
  6. J

    TED20 - small oil leak near lower link arm

    Ferguson (year 1952). There is small oil leak near lower link arms (where links installed rear end). I don't want to rebuilb rear end (is is not necessary) so could someone tell me what is good stop oil leak stuff (according oil)?
  7. J

    TED20 -52 valve adjustment

    I use only 98 octane petrol (not vaporising oil). Now I have ignition static timing. Is it possible that knocking disappear if I put timing little bit later?
  8. J

    TED20 -52 valve adjustment

    Why this Ferguson repair workshop manual commands to adjust hot?
  9. J

    TED20 -52 valve adjustment

    Is it possible to brink out valve pushrod cups/tappets (which are between pushrod and cam shaft) without to take off cylinder head? How? Magnetic?
  10. J

    TED20 -52 valve adjustment

    Sorry. I mean always millimeters (not inches)...
  11. J

    TED20 -52 valve adjustment

    Machice shop grinding rocker arms. Then I put valve clearance inlet 025 and exhaust 030. When engine was warm then knocking start (not cold engine). Now I put inlet 020 and exhaust 025. Now warm engine didn't knocking... Are these valve clearances ok?
  12. J

    TED20 -52 valve adjustment

    I think deep is .010-.015. Knocking problem? Grinding?
  13. J

    TED20 -52 valve adjustment

    I took rocker arms away. Rocker arms looks like this? Could these make that knocking noise? Do I have to "grinding"?
  14. J

    TED20 -52 valve adjustment

    I rebuild that motor 15 years ago (new bearings, piston rings...) Yes,engine do what I want. I have not heard any other petrol engines... Mayby now I found fault location (knocking noise). I ran the engine without valve head cover. I'm listening rocker arm shaft "feets".Three else's feet...
  15. J

    TED20 -52 valve adjustment

    Here is low quality video of my Ferguson. Hope so someone could tell me where that knocking is come from? I take spark plug lead off (one by one), but there is still same noise. http://vid38.photobucket.com/albums/e117/Buikki/Ferguson%20TED20%20videot/Ferguson%20TED20-video_zpslriisjzi.mp4
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top