(800) 853-2651
SHOP NOW

Recent content by jamesdebose-HT

  1. J

    Hydraulic fluid pushes out gearshift cover-it is pressurized

    The loader and 3 pt will work. I am planning to change the filter screen and fresh fluid to see if that helps.
  2. J

    Hydraulic fluid pushes out gearshift cover-it is pressurized

    I am fairly certain the level is correct.
  3. J

    Hydraulic fluid pushes out gearshift cover-it is pressurized

    I have a Yanmar 1500d and the hydraulic fluid flows out the gearshift cover (rubber boot) after the tractor runs for about 15 minutes. The fluid does have pressure behind it. I have installed the filter screen (about three years ago) and checked the vent tubes and none are clogged. I know the...
  4. Z

    IGNITION KIT FOR FRONT DIST

    Got the ignition kit from YT yesterday and was installing the ignition point contacts in the distributor and while installing the condenser and flat conductor I saw that the insulator in the points was a soft plastic that had moved out of place and shorted out the points. Took the points back...
  5. D

    O/T JD Van Brunt drill

    Just wondering if anyone here is familiar with an FB-A Van Brunt. I need a set of disc. They are hard iron bearings and are removed with key. I don't know where to find a key. It's a straight blade key I probably can make one. Just wondering if anyone has faced this problem?
  6. B

    Water Park!!!!!!!!!!!

    This is what happens when beavers and fish are more important than farmland. I've been here over 40 years and never seen a flood. The beavers have built dams along the creek and then it has built up with silt causing major flooding in some areas. When we phoned for help we just got a run...
  7. W

    case ih 3394 harsh shift

    Hello. i have a 3394 that i rebuilt the trans on. now that i can finally drive it, the tractor has a harsh/hesitation between power shift 2/3 and 4/5. same when down shifting, 5/4 and 3/2. i replaced the 3 pressure switches on right side of trans, swapped the c5 and c6 pressure switches. swapped...
  8. P

    Looking for 8n Camshaft

    Im looking for a camshaft for my 8n with front mount distributor. Yesterdays out of stock the only one Ive found is at agkits for a small fortune, thats ridiculous. Anyone have a source thats reasonable. Thanks
  9. 2

    Des Moines July 25 and 26

    My wife is going to a long arm quilting class in Des Moines July 25 and 26. Of course I am going as well. As a tractor enthusiast, can anyone recommend something for me to do while I am there. Thanks. Paul
  10. S

    J. Schiwbert

    Sorry to bug you again but I something's wrong with my email. So I guess we can do this over YT. How much would want for it and how wide is it? Also would it need any work? Thanks very much!
  11. T

    GL-1 Acting Like Fluid Coupling in Transmission?

    Cold weather, and I know the lift takes a while to warm up, but this was a new one on me: started the TO-20 to blade snow. Took it out of gear to let sit for a while, let out clutch, and tractor started to creep forward - out of gear. A few more minutes with the clutch in, and all was...
  12. G

    Side Mount Rotor - to a good home

    Was shipped a side mount rotor instead of a front mount rotor. Vendor made good on shipping me the correct one and told me to keep this one. I have no use for it. If I throw it in the junk pile side of the work shop it will get lost. Free to anyone that sends me an email first. (Yes.. Free...
  13. O

    carb problems

    I have a 56 utility 300. I need to get a carb kit and float, but there are no numbers on the carb so how do I order the correct parts!!! thanks!
  14. F

    HELP, big problems baling oats. What am I missing?

    Baler is an m&w 4x5 fixed chamber baler with the solid bars and sealed housing rather than belts. Starting up with this thing has been a NIGHTMARE!!! pickup plugs up constantly. I think we finally got things figured out on net wrap so it will work but if I can't pickup hay, who cares...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top