(800) 853-2651
SHOP NOW

Recent content by Jberg6

Yesterday's Tractor Forums
  1. J

    massey 22 three point

    Thats probably a tad too far for me to travel. I live about 40 miles west of St. Louis MO
  2. J

    massey 22 three point

    I am looking for a massey harris 22 three point hitch set up. If any of you have one for for sale or know of one please let me know. Thanks
  3. J

    Super 66 3 Point

    Brad Metcalf, I didn't recieve the e mail the other day. Could you please resend the message to [email protected]. Thanks
  4. J

    Super 66 3 Point

    I am looking for a a Three point setup for a 66 or Super 66. Also are their 3 points interchangeable with any other tractors. Thank you
  5. J

    30 oil pressure problem

    Thanks for all the suggestions Mike. I did have it running. I took out the oil pressure adjuster plug out and found the spring was missing. I put a new spring and some spacers in there and got the guage to show the desired pressure.
  6. J

    30 oil pressure problem

    I have a massey harris 30 with a 162ci continental. The motor was mostly rebuilt with new pistons and rings. The problem is that the new oil pressure guage doesn't show any pressure. I did take the line off behind guage and the oil barely seeps out. Please help
  7. J

    504 diesel blocks

    Well, shipping might be a bit too pricey. Our farm is about 40 miles east of St. Louis. Do u have any idea what it would cost to get them here?
  8. J

    504 diesel blocks

    I am looking to find a set of 3 diesel cylinder blocks with a bore of 4 5/8. I have 6 pistons that are 4 5/8 plus .30 over. Please respond to my email address if possible. Thank you
  9. J

    4020 hydraulic fluid overflow leak

    Yes its a hose from deere. I believe the line does go to the brakes...why would it have that much pressure
  10. J

    4020 hydraulic fluid overflow leak

    My 66 4020 pwr shift diesel has a line under the power steering pump in the dash that leaks. I believe its an overflow line that is only supposed to have around 15 psi pressure at the most, but when I start it, it will blow the rubber line, which is cappable of 150 psi. The old line was metal...
  11. J

    GBD block swap

    I was wrong on that casting # the blocks We have are #10A149A
  12. J

    GBD block swap

    I was wondering if any of you diesel junkies could help me with an issue I am having. I have a 55 GBD with a tired engine. I would like to swap engine blocks with a gas 504 that I have.(cast #1010248) Is this possible? Will they bolt up directly? Please help.Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top