(800) 853-2651
SHOP NOW

Recent content by jbevis

Yesterday's Tractor Forums
  1. J

    old!!!

    hey rich ,joe from neosho.will u send your phone no. to my e-mail. i lost it in my old phone. just wanting to catch up
  2. J

    old!!!

    [email protected]
  3. J

    old!!!

    i am trying to reach (old)rich!i lost his phone no.can rouse or anyone else help???
  4. J

    Gaskets

    3 pics of gaskets!!!
  5. J

    no lift!!!

    ok old! i'll do just that. thanks i'll be n touch.
  6. J

    no lift!!!

    when putting it back together rod was not bent and was seated in valve.everything with a couple inches fluid on it seem to b fine!!! could it still b air locked???
  7. J

    no lift!!!

    no i did not.but i left tractor running with pto engage for twenty min.s. and no lift!!!
  8. J

    no lift!!!

    sorry, this is on a 49 8-n!
  9. J

    no lift!!!

    put in a hydraulic pump overhaul kit(part no. hpok1)a new lift cylinder and piston with rubber o-ring and leatther backup washer.new hydro fluid,all new gaskits and adjusted linkage per fo-4 manual.and a new pto shaft. the pto shaft spins great but i have no lift in the arms!what have i done...
  10. J

    cylinder gaskets

    53-60 ft. lbs! thank you r.geiger!!! i bench fit the new pto shaft through the hydro pump it fit fine. i dry fit the pto shaft to the coupler and got a quarter inch of sitting it.once i get my gaskets can i tap the pto in all the way,do u think??? thanks for your knowledge and support. joe
  11. J

    cylinder gaskets

    thank you r. geiger and tall t. that helped alot!!! and where do i find torque no.s ???
  12. J

    cylinder gaskets

    would you tell me what order the neo. and leather gasket go on a 8n lift cylinders piston. please and thank you for any info.
  13. J

    PTO SHAFT REMOVAL

    FIRST OF ALL I APOLOGIZE IF I OFFENDED YOU OR ANYONE ELSE!MY WIFE TOLD ME IF YOU TYPE IN CAPS PEOPLE CAN GET OFFENDED!!! I DONT TYPE OR POST MUCH SO CAPS WERE EASIER!!! :?
  14. J

    PTO SHAFT REMOVAL

    WHAT ABOUT THE CAM FOLLOW PIN??SHOULD IT BE PERFECTLY ROUND OR IS A FLAT SIDE TOWARD THE LIFT ARM OK?? THANKS FOR THE HELP YOU GUYS ARE ALL AMAZING :lol: :lol: :lol:
  15. J

    PTO SHAFT REMOVAL

    Concerning the lift cylinder ROD! Where it connects to the lift arm with the pin, how much play should be in the rod? Im talking about where the pin connects to the rod,should it be loose or tight??[/i]
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top