(800) 853-2651
SHOP NOW

Recent content by JBKINWA

Yesterday's Tractor Forums
  1. J

    MF 35 Utility PTO Lever

    meant to edit hit post instead, but I think you get the gist
  2. J

    MF 35 Utility PTO Lever

    look at the end of the shaft where it goes through the lever. If it has migrated inward (broken pin) the inside lever will not be engaging the detents. The detent pin if I remember right is spring loaded and possibly it may be stuck. I made a lever for mine a couple of months ago. As long your...
  3. J

    MF 35 Hydraulics

    Your right when you say longer and more expensive to do that way. When I fixed mine recently I went with the new style. Mill time was expensive when I needed a lathe that would accept 3 3/8" stock. I had already lost too much time getting the repair done and needed the machine. But if you decide...
  4. J

    MF 35 Hydraulics

    Best answer is to mill lower piston ring groove to accept a .250 O-ring. That was Massey's fix but was never put into production. It was in an old service bulletin. You would have the 2 cast upper rings and the O-ring. They didn't use the Teflon wear ring at that time but I don't see why...
  5. J

    MF32 Loader control valve

    thx, sent a response.
  6. J

    MF32 Loader control valve

    I have been trying unsuccessfully to get the parts to rebuild my loader control valve. I am not even finding rebuilds. Does anyone know of a aftermarket replacement? The return to tank is built in as part of the valve mounting plate. My control valve part number is 708582M91.
  7. J

    MF40/40B hydraulic parts

    There are only 3 places to adjust. I came up with the nuday bushing dia by measuring several pics of the assembled tool and came up with .375 ID and 1.0 OD on bushing. when I was done all lever positions for function were in spec. I did not have to move quadrants. :) Just think I have a bad...
  8. J

    MF40/40B hydraulic parts

    I give up, to much pain in hiney to load images. sorry guys, if really interested I will respond to email, send a request.
  9. J

    MF40/40B hydraulic parts

    pics, try again
  10. J

    MF40/40B hydraulic parts

    pics of rigging
  11. J

    MF40/40B hydraulic parts

    This is the early version of the 40B hitch cover and linkages. Also an easy solution If you do not have the spring scale for set up. A ladder pulley and the 3lb weight. The rigging was very easy once you have the special tooling. I don't know how u could be even close without it. While I am...
  12. J

    MF40/40B hydraulic parts

    I need a 1661427M91 mounting block assembly to convert my older MKIII pump to accept a cartridge style relief valve. Does anyone out there have one they would be willing to part with? I know there are those of you out there with the experience and knowledge to help me get this unusual girl back...
  13. J

    MF40/40B Internal Hydraulics-No dashpots- Final adjustments

    This will be last post. wish the best for everyone.
  14. J

    MF40/40B Internal Hydraulics-No dashpots- Final adjustments

    I could use some input and was wondering if anyone has experience with this system. New post as I realized we were comparing apples with oranges. I spoke with the original owner and this tractor was equipped this way from the factory. He had hired someone to fix this many years ago (not a Massey...
  15. J

    MF 135 hydraulic controls

    The dashpots were removed when they added the slide valve on the side of the rear casting of the pump to control response rate. It still works basically the same way. (relieving pressure in the intake gallery to allow the control valve in the pump to move to the discharge position). Although it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top