Recent content by JC Davis

  1. J

    Catching the gas when draining a IH 330 fuel tank?

    "Be VERY CAREFUL sticking an vacuum in the tank. The fumes may explode when they contact brushes in the motor." Yeah, I think that could make a very effective gas bomb. I was planning to make sure the tank was bone dry. But I have had a better idea. I'm going to try sucking the fuel and dirt...
  2. J

    Catching the gas when draining a IH 330 fuel tank?

    That looks doable. Thanks!
  3. J

    Catching the gas when draining a IH 330 fuel tank?

    My 330 utility too often ends up with debris in the fuel tank. This time, I want to drain the tank, let it dry, and vacuum the junk out of it. I've drained it a couple of times over the last dozen years, but have not devised a way to keep the gas from running down the side of the casting and...
  4. J

    IH 330 PTO disassembly

    I got that plate off, made a deep socket from tubing to get the nut off. Made a puller as noted above. Got it all apart, swapped the two bands and reassembled. Works perfectly after adjustment. Thanks to all. Jim
  5. J

    IH 330 PTO disassembly

    I pulled those bolts still visible in the picture, but they are all short and meant for fastening the guards in pace. The diagram and text indicate a nut has to be removed from the PTO shaft, so I need to get the bearing retainer plate off. It may just be tightly stuck to the gasket....
  6. J

    IH 330 PTO disassembly

    I have an IH shop manual for this tractor but still have a question. It looks like I need a special puller to get the back cover plate off. Would never find an IH one made for this, but am stumped as to how to figure the bolt circle for three bolts. Also, the text seems to say that the bearing...
  7. J

    IH 330 PTO

    I'll give the adjustment a shot tomorrow. Thanks. Jim
  8. J

    IH 330 PTO

    Thanks for the info I'll make a note of it and keep it while I decide on a course of action.
  9. J

    IH 330 PTO

    That makes senses Cmore, but I already did that--often and all the way down to 1st sometimes. I'm thinking of sharpening the blades. The drive band adjusting screw is in below the top of the jam nut.
  10. J

    IH 330 PTO

    My 5-foot bushhog bogs down and makes the PTO clutch of my 330 utility slip in heavy going. I have adjusted the drive band to where it is hard to engage. Does that mean I need to replace the band, and if so, where can I buy the part?
  11. J

    IH 330 UT oil pressure

    I did not flat sand the oil pump cover. I did notice that the idler gear in the pump stood a couple of thousandths higher than the drive gear. Was tempted to try to flat sand that to length. Probably ought to do it, then flat sand the cover... IH spec say .003-.006 clearance. I'm going to talk...
  12. J

    IH 330 UT oil pressure

    First tractor I ever bought that had worse problems than I had thought. Makes about 25 pounds of oil pressure when first started (with two cans of STP added). When it warms up, it will hardly make 5 pounds of pressure and there is a definite knock at medium and low engine speeds. I had the oil...
  13. J

    330 UT oil pan removal

    Being impatient by nature, I took some of the weight off the front wheels with a jack and loosened the rear pivot bracket. The bracket stayed put. When I raised the jack a little, the bracket lowered. So, I pulled the three bolts and slowly jacked up the front until the bracket was about 4...
  14. J

    330 UT oil pan removal

    Do I have to remove or lower the front axle and stabilizer brace to remove the oil pan on my 330 UT? I don't have a parts diagram or book to see whether the front axle might pivot, allowing the rear brace to be lowered enough to remove the pan. Thanks. Jim
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top