(800) 853-2651
SHOP NOW

Recent content by jd4010guy

Yesterday's Tractor Forums
  1. J

    830 2 cylinder fuel transfer pump

    Thanks Bob, the grease sounds like a good idea.
  2. J

    830 2 cylinder fuel transfer pump

    I just put new seals in the fuel transfer pump on my 830. After reassembly the shaft that couples with the end of the camshaft seems to turn a lot harder/stiffer than before the new seals. Is this normal or is there a different problem a brew? I cleaned the mating surfaces with 1000 grit...
  3. J

    4010 battery

    I have 1961 4010 Diesel that the right side positive battery terminal corrodes making a lot of residue on the cable/battery terminal in a short amount of time - a week to two weeks. The negative terminal also corrodes but not to the extent of the positive terminal. At that point the tractor...
  4. J

    830 rear rims

    Thank you!
  5. J

    830 rear rims

    Does anyone manufacture 18 x 34 single bevel rear rims for a 830? Thanks.
  6. J

    Paint job

    Going to paint my 830: Any thoughts on what a guy might have to pay to have the sheet metal painted professionally? Thanks.
  7. J

    4010 belt pulley

    Thanks Tom!
  8. J

    4010 belt pulley

    Hi folks, I am looking for a PTO driven belt pulley for my 1961 4010, if you have one to sell or know where I might find one give me a shout. Thanks!
  9. J

    Air compressor struggles

    buick&deere: By struggling I mean that as the pressure builds in the tank the pump has a progressively harder time as the pressure builds until the pump will no longer turn and the belt squeals and the motor can no longer turn the pulley on the pump. ss55: I will have an electrician check that...
  10. J

    Air compressor struggles

    I have a Ingersol Rand ss5 compressor I bought from Tractor supply a few years ago. It started struggling and would stall out at 50 - 60 psi. I replaced the valve plate assembly, gaskets and check valve. The first time I ran after replacing parts it ran up to 100 psi and then stalled again and...
  11. J

    830 2 cyl crankshaft

    Thanks to both of you. Your help is greatly appreciated!
  12. J

    830 2 cyl crankshaft

    I checked the clearance of the main bearings on my 830. the right side measured 0.0009 and the left (flywheel) side 0.011. The service manual says if it is 0.012 then the main bearings should be replaced and the crankshaft serviced. Is it feasible to measure the crank journals where the outer...
  13. J

    2001 JD 335

    Has anyone tried to retro fit a wash port that is available on the new mower decks to a deck for a 2001 JD 335 54 inch wide? If so does it work well? Thanks!
  14. J

    2001 JD 335 garden tractor

    Has anyone tried to retro fit a wash port that is available on the new mower decks to an older deck (2001)? If so how'd you make out? Thanks!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top