(800) 853-2651
SHOP NOW

Recent content by jd40203020

Yesterday's Tractor Forums
  1. J

    620 water in transmission

    Will do. Learning lots about this that i never knew.. Pto has water too. Going to remove pto/ rockshaft housing and replace oil seals part # AA5247R . In looking up parts I dont see a gasket between the small housing that holds the seals and the large pto/ rockshaft housing. Am I missing it...
  2. J

    620 water in transmission

    Cant believe its that much condensation but could be... I doubt that oil has been checked in over 30 years.
  3. J

    620 water in transmission

    I gave a 620 that used to sit outside a lot when my parents were darming. Recently its parked inside and does not get run often. I have never checked the transmission oil, so i decided i should and found about 4 gallons of water and no oil in the transmission. No idea when oil was ever...
  4. J

    4020 diesel oil temperature?

    I have the small oil pan, so I'm watching to see if it gets too hot. Hottest it has been so far is 205. Thank you all!#
  5. J

    4020 diesel oil temperature?

    What is the normal enging oil temperature for a 4020 diesel? What is too hot? Just hooked up a temporary gauge after an unexpected overhaul to make sure everything is ok.
  6. J

    Looking for early 4020 head bolts part #

    Thank you all for your help. With the help of the service manager at my dealership we looked up the part #'s and torque specs today and got them ordered. As many if you stated the correct bolts for the early 4020 are grade 8 and will need to be re-torqued. The torque /turn style bolts are...
  7. J

    Looking for early 4020 head bolts part #

    Any chance you could take a picture of it and post it?? That would be very helpful!
  8. J

    Looking for early 4020 head bolts part #

    Are the newer 4020 blocks different as far as the threads? The new bolts are offered for them, but we're not used when they were new from the factory?
  9. J

    Looking for early 4020 head bolts part #

    First I've heard of this... everyone I have talked to has said to change to the new bolts. This site has a wealth of knowledge... what's everyone's oppinion?
  10. J

    Looking for early 4020 head bolts part #

    R33180. Are the part numbers you listed the original bolts with washers? Just to make sure, do the new torque and turn bolts have the flanged heads with no washers? Hoping I get the right stuff!
  11. J

    Looking for early 4020 head bolts part #

    I am having some trouble with my dealer not being able to find the correct head bolt kit for my 4020. It is a 64 with the big injectors. Head casting # R33250. I was hoping to get the newer torque and turn style bolts, but they say they are not available for this head. Is this true or does...
  12. J

    Early 4020 Head installation questions

    Sounds like I'm buying new bolts! Is the torque pattern and spec the same as the original service manual? Thank you all for the help!
  13. J

    Early 4020 Head installation questions

    I am going to be istalling the head on my 1964 ( big injectors) 4020 diesel. I want some expert tips so I don't end up with annoying oil leaks near the right rear corner. Head has been plained and valves replaced. Is it best to install the gasket dry, or should I use a spray on copper head...
  14. J

    JD 328 baler uneven bales

    Finally got to test the baler today. Found one of tge hay dog springs broken. Was bottom one so I doubt it was causing my problems. The feed fingers needed to be timed and the chain that drives them was very loose. Was easy to do with the manual and seems to have worked. Baled 750...
  15. J

    JD 328 baler uneven bales

    Yes. All 3 are there and they function correctly.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top