(800) 853-2651
SHOP NOW

Recent content by jdd51

Yesterday's Tractor Forums
  1. J

    Schwartz tie rods

    I have a 1650 Oliver that has an after market wide front. The ball joints are larger than standard Oliver having a 3/4 -16 stud with approximately 3/4" to 1" taper. Standard Oliver has a 5/8 - 18 stud with corresponding smaller taper. Where can I find tie rod assemblies or replacement ends to...
  2. J

    1650 stalling issue

    I have a 1650 gas. Almost 50% of the time, on a fully warmed up engine, the motor stalls out when letting out the clutch. It also stalled out when raising the loader. The motor will start back up fine, but needs full choke to do so. Blows black smoke and runs rough for a few seconds, then...
  3. J

    Super C Pesco pump

    Thanks for trying. Next option is the salvage yards for a junk pump.
  4. J

    Super C Pesco pump

    Thanks. Appreciate the help.
  5. J

    Super C Pesco pump

    Does anyone have source for part #'s 17, 18, and 19 (ball, spring, and cap screw) in the drawing? Having pump issues and discovered them missing. Port was sealed with an 1/8" pipe plug. Thanks for the help.
  6. J

    Super C hydraulic problem

    Thanks. Any idea where I can get the spring, ball, and cap screw for this Pesco pump? The port is capped with a 1/8" pipe plug. Would these items not being in the pump cause the issues? Thanks
  7. J

    Super C hydraulic problem

    Thanks for the advice. My tractor has the Pesco pump with a seal, not an o-ring. The last time I tried the pump, with a newly installed seal, the engine did not lug down. It did in an earlier try. The last time I tried it I did see slight movement in the rocker arms when I was working the...
  8. J

    Super C hydraulic problem

    After sitting for several years I got this tractor running. Before storage the hydraulics were in working order. Long story short, the hydraulic pump pumps fluid into the crankcase. I've put a kit in the pump as the original seal was shot. No help still pumps into the crankcase. The gear shaft...
  9. J

    1650 hydraulics

    Thanks for the advice. I decided to go with a Westendorf quick attach system and modify the bucket to accept it.
  10. J

    1650 hydraulics

    Thanks for the reply. What I'm concerned about is that the spear on the front edge of the bucket will have too much leverage for the hydraulics. Has anyone used a setup like this?
  11. J

    1650 hydraulics

    I have a 1650 gas with a Schwartz 1800 loader. For convenience this winter, I would like to put a a clamp-on bale spear on the bucket. Does this tractor have enough capacity to lift a bale of, say, 1800 lbs. or should I remove the bucket and buy a spear to mount on the loader? Thanks.
  12. J

    1650 hydraulics

    Thanks for the help.
  13. J

    1650 hydraulics

    I just bought a used Shaver HD10 post pounder to run on my 1650 gas. The previous owner plumbed the 1 1/2" return line directly into the reservoir via the fill hole. I think he was running the pounder on an AC. My question is where can I run the return line to the reservoir on the 1650? I've...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top