(800) 853-2651
SHOP NOW

Recent content by JDinMi

Yesterday's Tractor Forums
  1. J

    990 MoCo

    I have two 990's and one has had to have all of the sprockets replaced twice in twenty seven years of use. Usually the lower drive sprocket will also be worn as all sprockets that a bad chain ran on. I turned the worn teeth off and bored a weld it sprocket to the sizes needed to put them back...
  2. J

    henry rifles

    Hi, I own two golden boys .22 and .22 mag. I also own a big boy .44 mag. Henry sells a cantilever scope mount which is solid and works well. You just need to follow their directions for drilling and tapping. The rifles are very accurate and extremely attractive. My only dislike, and I have made...
  3. J

    460 / 560 glow plugs?

    Hi, I just checked and Ebay has two venders with a set of six, free shipping for $78. Thats where I got my last set. Good luck
  4. J

    head gasket

    Hi, Did you replace the sleeves when you did the rebuild? I had a problem with the new sleeves protruding higher than the recommended .003-.007 Because of that I couldn't get my head gasket to seal and I keep getting water into the oil pan. Got the tips right here a couple years ago. Great...
  5. J

    Boyds stocks - need a new handle on a tool

    I purchased a complete thumb hole laminated set for my Encore. Four different fore ends. I will buy from them again. Very good fits and pepper colored laminate is quite attractive to me.
  6. J

    Round baler tractor

    IH Hydro84, IH8420 I make at least 500 per season, last five years.
  7. J

    International 990 Haybine

    I"ve used mine for 20+ years. Had to replace chain and sprockets twice. Turned old teeth off and welded machined sprockets back on. Much cheaper than dealer parts. Some have mentioned that the woble box breaks where it"s attached so check for cracks or welds. Keep the guards in line so that the...
  8. J

    Adding rearend oil to 560

    Sorry fat fingered ..should be full plug.
  9. J

    Adding rearend oil to 560

    Yes the fill hole is the three bolt cover and the fill plug is ahead of the clutch pedal.
  10. J

    560 fast hitch to 3pt?

    Look at these if you want a three point and remove the fast hitch. http://www.saginawcountytractor.com/
  11. J

    CIH 695

    Hi, I'm going to look at a 695 that's quite rough sheet metal wise, all the front grill parts are missing, but owner says the engine runs well. My question for the wise folks is that the hydraulic when warmed up is slow lifting the three point and steering is tight and jerky. Could this just be...
  12. J

    Hesston 530

    Hi, the belts are 4.8" x 364" I have a CIH 8420 same as your 530 nice little baler.
  13. J

    jd 24 T missing ties need advice

    I had an older model 14T and it did the same interment problem. Turned out to be the rollers that drive the sweep arm to the knot had flats worn on them. Put new round ones back on , adjusted the arm to strip off the knot, and good to go. I have noticed that the New Holland balers use brass...
  14. J

    coolant getting into oil pan on my Farmall c

    Thank you for the idea's to get me on track. I do have a SnapOn radiator pressure tester to double check the sleeve O-ring gaskets. The thing is that it now leaks more after I tightened the head bolts 5 more pounds??? I drilled and tapped another drain plug with a petcock installed, so I drain...
  15. J

    coolant getting into oil pan on my Farmall c

    Hello, I overhauled this C late last fall. It runs great, I plowed snow and now want it to rake hay. When I installed the new sleeves I noticed that they all were taller than the original, in the height exposed on the block. I mic'd them and they all ran from .011 to .0125" in height protruding...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top