(800) 853-2651
SHOP NOW

Recent content by JDNPC

Yesterday's Tractor Forums
  1. J

    Running Rough and I'm out of Ideas

    sounds like you need to double check the govenor detent linkage and govenor internals.
  2. J

    What is a 40C worth?

    if you have an extra $3k to spend on redoing the clutches the right way and another $2k for the blade and cylinder....then locate one ready to go and pay the piper so you can jump on it and go. nevermind all the heavy lifting with a chain hoist or engine hoist. tracks and clutches cost is...
  3. J

    3010 steering

    TimS has your answer. Mine had same symptoms and he rebuilt the valve. Good as new.
  4. J

    Show

    I knew you couldnt resist Tim. Howard, you are a great salesman. I will be there as well!
  5. J

    JD 40 wont start ?

    you may want to tap the side of the carb with a plastic handled screwdriver. the float may be sticking after sitting awhile and only allowing small amounts of fuel to pass allowing it to fire erratically.
  6. J

    3010 Diesels - School me on them

    it's a 5K set up. more than that is your opinion. I've owned one with the same set up and has performed outstanding. the tilt on my loader is more powerful than the dead lift arms. I can get a GP off the ground to load on a trailer, but it is ran directly off the pump. tranny rebuilds will...
  7. J

    1951 G rod bearing help

    Just had my F1047R rods cleaned up. New piston pin bushings fitted and machined and bought the 2 piece .020 rod bearing inserts to match the rod journals that were ground. Do I need to use shim stock to clearance these correctly or what? The bearings snapped right in and feel good when snugged...
  8. J

    2 row planter

  9. J

    2 row planter

    yes.
  10. J

    late styled G .125 over piston purchase

    I believe Hinrichs stated 12,000ths when we spoke on the phone yesterday. Said they would ship the info with the pistons and I will ensure the machine shop gets it to finish honing the cylinders properly. Nice people to help me out when I called. Thanks for the referral. Great reminder on the...
  11. J

    late styled G .125 over piston purchase

    after all the posts I've read here and over on the pulling forums, I am needing a great source for a set of .125 over pistons for my freshly bored late styled G block. I am assuming high compression aluminum ones are the answer but I am having a hard time locating them from a reputable source...
  12. J

    24B planter

    I can't afford a lilliston picker-even an antique one as of yet, so if I can get a few youth baseball teams to help out, I may get a start. Still looking for a picker though.
  13. J

    24B planter

    I have a Hoover 1 row digger with an inverter that I hope will save my back this season. I think it will do just fine enough as I by no means claim to know what I'm doing. Thanks for all that knowledge. I know tha's not printed in a manual anywhere LOL. I am considering selling off a couple...
  14. J

    24B planter

    Thanks for the info. I saw those diagrams online at JDParts but they are obviously NLA when searched, so I am currently in the market for a set. Off to the classifieds I go.
  15. J

    24B planter

    Looking to plant peanuts again this season and not by hand as an acre is in order. I picked up two 24B units on a tool bar for my 3010D and wondered what plate # system works best with unshelled or shelled nuts that would drop right in the seed hopper? I see on JDparts they have a high speed...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top