Recent content by jedagi

  1. J

    Subsoiler ID

    I have a single shank parobolic subsoiler. It is cast steel and mounts to the cross drawbar on the lift arms of the tractor. The letters cast in the implement are WSB Co. Does anyone know anything about these?
  2. J

    65 Massey Ferguson generator, voltage regulator, volt meter

    My apologies. I restored this tractor a couple years ago and i replaced a couple of the gauges that was busted. The only gauge i could find at the time with a stainless bezel was a volt meter. And you are correct about the negative eight volts. I was thinking one thing and typing another. The...
  3. J

    65 Massey Ferguson generator, voltage regulator, volt meter

    My tractors volt meter gage started showing negative 8 volts. I removed the battery cable for a few seconds then put it back on the battery post. The gage shows charging, up to 14 volts depending on rpm. But after a few minutes the volt meter will drop back to negative 8 volts.
  4. J

    MF 50 rear light

    This part number is a transmission part.
  5. J

    removing and replacing wire mesh in 65 oil bath clener

    If I remember correctly I took the breather hose off. Removed the screws that hold the breather assembly in place. Then lift the hole thing out threw the top. Seems like I had to take the oil cup and clamp off to get it lifted out. Once that is done there's a baffle that above the oil cup that...
  6. J

    MH and MF Implement colors

    The #64 has a Massey Harris name plate on it. It has gray paint on it but has been repainted. The p ao 21 has a ferguson tag and red paint on it but has also been repainted. The MH has remnants of a decal on each side that said Massey Ferguson .
  7. J

    MH and MF Implement colors

    I have 2 disk plows.#64 and P AO 21. One is red and the other gray. I know many of them had gray paint. Was any of them originally red?
  8. J

    Tool for power adjust rims

    I used a good flat ended punch and a hammer. The punch was about 3/8 diameter on the end and ground flat. Set the punch at an angle and drive the cam lock in the unlock direction. The first one can be tough but as tension is released from the rim they get easier. Also pick up a can of power...
  9. J

    JD disk plow (400) series? value

    In my recent Implement search I ran across a john Deere drag type disk plow. Sadly I can't remember if it was 2 or 3 disk. It has a trip lever to raise and lower it with a heavily weighted tail wheel. What value would this plow have.? It looks to be in good shape except for rust.
  10. J

    Ferguson Disk plow questions.

    I just bought 2 of these. One is a massey harris bent tube 2 disk plow . It needs some parts. The other is a Ferguson 3 disk plow, straight tube with a pig tail on the back that hold the 3rd disk and the tail wheel. Its a P-AO-21. I may know of another but I'm keeping it on the down low until I...
  11. J

    Paaint shade

    The spray cans seem to have lots of metallic in them. I got a can for touch up and it real sparkly metallic.
  12. J

    massey ferguson 65 decathe proper l locations

    Diesel Matic This spell checker drive me nuts. Lol
  13. J

    massey ferguson 65 decathe proper l locations

    Yes, mine is a high crop diesel native. I've seen the pull from draw bar decal placed left of the pto shaft/top link arm on the rear end housing. I see a decal in many pictures. Its on the right side of the lower dash panel. I guessed it to be starting instructions. Thanks Keep them coming.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top