-
J
stihl 041av hand guard adjustment
there are many versions of 041. some had hand guards, some nothing, some with chain brake. the 'GUARD' that i got for 041 fit via 2 screws but is held up by the brake handle. so.... i got a brake handle & placed in my guard. aok now -
J
stihl 041av hand guard adjustment
has good spring with one end in saw body. flops towards bar. i tighten slotted screw at end but it does nothing. parts diagram shows no additional parts. -
J
mf super 90 1100 2nd gear pop out
going downhill, sometimes in 2nd (hi or low) will pop out of gear with mulitpower on. is this a linkage adjustment ? is there a way to fix ?- jim_uny
- Thread
- Replies: 2
- Forum: Massey-Harris & Massey Ferguson
-
J
ferris 3 wheeler lawn mower
used a 2 inch hex head bolt with 1.5 washer. 3 bolts on on gas tank support. removed inner & loosened outer & tank suppport tilted leaves plenty of room.- jim_uny
- Post #2
- Forum: Garden Tractors
-
J
ferris 3 wheeler lawn mower
have criterion 320 same as ferris pro cut 61. have eaton hydrostatic with fan on top. bolt for fan blade came out. take 1/4 - 20 x 3/4 hex bolt with allen. not enuf room without removing axle. can i fix hex headed bolt in & turn with wrench? has anyone removed transaxle & what is involved ...- jim_uny
- Thread
- Replies: 1
- Forum: Garden Tractors
-
J
belsaw 450 trueing / dressing tool w/ diamond nib
it is expensive tool. how does one replace diamond nib ? have email into belsaw but does one have to cut & weld in new one ? -
J
pioneer chainsaw farmsaw gas cap
i looked up parts diagram & it is vented with plug & hole. i will take apart & use a welding tip cleaner to clean vent hole -
J
garrett tree farmer log skidders
have searched but see no info on company's website & where to get parts. does anyone know or contact for dealers ? -
J
77 row crop
do you mean the square unit base with hy pump & control arms ?- jim_uny
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
J
77 row crop
got water in rear end oil. drained, flushed. store inside. other than shifter rubber boot cap, where can water get in ? thanks- jim_uny
- Thread
- Replies: 6
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
J
jd 38 / 3800 adjusting for hmec 243 head
did you have a slip clutch on 243 head drive unit for 3940 ?- jim_uny
- Post #1
- Forum: Implement Alley
-
J
jd 38 / 3800 adjusting for hmec 243 head
how did you attach plastic. i fumbled upon jd part # r52423 on ebay. does that look correct ?- jim_uny
- Post #1
- Forum: Implement Alley
-
J
jd 38 / 3800 adjusting for hmec 243 head
was unable to upload page 50. give me your email & i can send.- jim_uny
- Post #1
- Forum: Implement Alley
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy