(800) 853-2651
SHOP NOW

Recent content by Jmo1999

Yesterday's Tractor Forums
  1. J

    Another Car-Nundrum

    Can you put a nut on it and weld it to remove the broken bolt? Need to disconect the battery if you weld on a car. I have put the coils on without the bolts.
  2. J

    Way OT 1996 F150 Starter actuator rod?

    I have replaced a lot of those, it takes me about 40 min. I have the tools to do it. part is cheap. I would not replace the whole column. Take it to a repair shop, labor time is like 1.5 hrs.
  3. J

    Compressor value

    I have a 30 gal. horizontal tank that that compressor went bad. It was a 1986 quincy.
  4. J

    More distributor questions

    R45T is the next hotter plug, you don't want a extended tip plug. However if they are black you have a different problem. Carb running rich/jets? You should check your timing also.
  5. J

    GM 4 cylinder.turbo n a full size pick up???

    How is Ford trying to reinvent the wheel, they have an actuall V-8, V-6 ecoboosts, 4 cyl. ecoboosts that make good power, unlike GM that tried to make a V-8 run on 4 cyl. which is junk and now V-8 that will run on 1 cyl. at times. Hmmmmmm
  6. J

    John Deere Paint question

    Yes the JD paint is very good paint, use their hardner with it. The paint is cheaper then Dupont, PPG or Valspar.
  7. J

    2006 Buick LaCrosse

    I always said one of the best cars ever built was a 1997-1999 Buick Lesabre, however the 2000's were not as good, there are some bad ones and some good ones. The Lucerne was poor, the Lacrosse seems to be better. The intake gaskets don't leak, its the intake plenum that has to be replaced by...
  8. J

    ADVICE

    I did that in 2013 with half the field. planted with JD 7200, yield was the same, I had the same pop. for both 30" (140,000) and 15" (set at 70,000 and turned around)
  9. J

    '04 Dodge Ram

    you get what you pay for
  10. J

    Wow..... What A Disappointment!

    Charlyn power steerings where the "cats meow" My dad has several tractors that we use with them. <image src="http://forums.yesterdaystractors.com/photos/mvphoto18841.jpg"/>
  11. J

    Hey Tile Guys

    You can just put backerboard down with thinset. no need for another layer of plywood.
  12. J

    Stuck Farmall M

    Once you get the piston out you just need a dingleberry hone. I helped dad unstick engines like that before without taking head off and would use diesel fuel and ATF, would never have a problem with them burning oil, and they would get worked
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top