(800) 853-2651
SHOP NOW

Recent content by John(UKI)

Yesterday's Tractor Forums
  1. J

    Ferguson TO-30 Engine Speed

    Check the Throttle and Governor linkage for worn parts, especially the holes. If there is wear here it will be floating around all over the place. Make sure with the engine stopped and the throttle wide open, that the throttle linkage moves very easily and isn't catching anywhere. You need to...
  2. J

    TO 30 wont start

    There is a small amount of adjustment on these switches. If you slacken the screws securing it to the top of the Clutch Housing slightly and slide it forwards and tighten, you may find that is enough to allow it to work again. If it doesn't you need to replace the switch. They have them on this...
  3. J

    TEA20

    That oil should be 10W/30...John(UK)
  4. J

    TO20 axle sure seal

    Email me and I will send you what you need. With a TO20 you can fit "Sure seals" from this site that will save you a lot of work..John(UK)[email protected]
  5. J

    post hole digger

    Of course it will, just think of all the older grey ones that only had a single clutch, they worked them ok...It's not like you were moving as well as operating the PTO....just keep lifting and lowering as you dig the hole, if you let it go too deep you will have to wind the auger out by hand...
  6. J

    TO 20 transmission problem

    Whoever changed the Safety Switch probably couldn't find a genuine one, they were in short supply at one time and all kinds of lash ups were done. But you can get a switch easily from this site. But if it won't go into reverse, the switch is on the same selector rail as Reverse and it may just...
  7. J

    TO-30 Hangs Up in Gear

    In addition to having an Over-run clutch on the PTO of the Mower, are you running the mower too low and the blade is held from turning by the soil. The Blade should never touch the ground, it should be set so that it misses it completely and the back of the Hog should be set at least 2" higher...
  8. J

    6 to 12 volt conversion Starter Motor

    The 12 volt TEA starter has a very long Bendix shaft and will not interchange with a 6 volt starter because the Transmission Housing and the Cyl Block will not accept it. On TE's and TO20/30 there were some differences in the Flywheels but not on all, some will interchange, some TO's have the...
  9. J

    6 to 12 volt conversion Starter Motor

    That Starter with the solenoid has been available for a while now, but there is another starter that looks exactly like the original 6 volt type but it is a 12 volt. It is available from the YTForum site as..(Part No: 4858MFGXL_12V) price $179.95 USD. Most of the suppliers of parts seem to have...
  10. J

    to35 massey

    The PTO guards are nearly all a standard fitting, you can easily get one from this site or maybe local to you. They are the same fitting on all MF tractors that use the 4 bolts around the PTO for the check chains.. John(UK)
  11. J

    Ferguson tea20 STARTER MOTOR problems etc HELP!!

    Check the ground lead where it attaches to the back of the Dash Panel, you may find that the bolt to which attaches gets warm. If it is the Ground Lead then get a longer one and attach it to one of the bolts close to the starter. It should be wired Positive to ground. You can also check the...
  12. J

    TO20 over reving

    It could be the Governor or simply the setting of the throttle linkage. Start the engine and check if the spring in the middle of the vertical rod at the back of the Generator is stretched, if it is then the setting on the clamp on the long torque rod over the top of the Engine and at the front...
  13. J

    Source for steering box oil seals

    You will see that you can't pass the Oil seal over the shoulder on the Drop Arm, so you need to grind it off and then you can. It isn't used for anything, it was so they could machine it in manufacturing. John(UK)
  14. J

    Correct wiring ignition switch for Standard 23 C

    The switch arrangement on the UK version and I think that Detroit used the switches from UK in the Engine kit. was just turn to clockwise to start Engine normally without heaters BUT turn counter clock to Heat and then Heat and Start..John(UK)
  15. J

    TO-30 bolt holding step and power take off lever

    Did you think that I had been playing that word game Scrabble again and that was one that came up...lol! John(UK)
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top