(800) 853-2651
SHOP NOW

Recent content by johndeere37

Yesterday's Tractor Forums
  1. J

    oliver 880 head

    it is a gas motor i was just wondering what other heads bolted on i was gonna buy another head to have bigger valves, etc. but thanks
  2. J

    oliver 880 head

    what all heads will fit on a 880 motor
  3. J

    head work?????

    i have a stock 880 that i pull i was looking into head work any advise????
  4. J

    head work??????

    i haver a stock 880 that i pull i was looking into head work any advise????
  5. J

    77 in a 66

    the only reason im wanting to do this is because i wanted something different then everyone else. because i bet nobodys got one like this im not really wanting to pull it but a couple of times just something diff to have ya know?
  6. J

    77 in a 66

    the reason that im wanting to do this is just to do something different and the main reason is because we tractor pull and where we pull at they have a 3000 pound class and as light as i can get my 77 is 4000 im not taking it apart but if i can find like a 770 or 77 motor to stick in a 66 if its...
  7. J

    77 in a 66

    could you squeeze a 77 6 cylinder into a 66 with some modifiactions gas tank out shorten up the driveline and run an electric fan and take the old fan off
  8. J

    oliver speed??

    thanks chuck
  9. J

    oliver speed??

    no im running 3rd and 4th gear but theres a fellow that we pull with thats good a tractor like mine perty well identical but he can run almost 2mph faster than i can in the same classes and are motors are the same. so what i figure is that it is in the gearing?
  10. J

    weight of oliver 77 with pressed steel 13.6

    yep what he said if you take all that off 3500 it what it should weigh
  11. J

    oliver speed??

    How do i get more speed out of my oliver super 77 for pulling.it has a diesel rear end that is all i know about the rear end. i have enough power but im wanting to go faster than what i am is the some kind of gear you change or what? thanks steve
  12. J

    weight of oliver 77 with pressed steel 13.6

    does it have the belt pulley is it a super or not and does it have a deisel rear end those are heavy
  13. J

    allis wd45

    how much hp can you get out of a wd45 allis for pulling and need an estimate on price thanks steve
  14. J

    super 77 engine

    thanks chuck
  15. J

    minn moline z

    how much hp can you squeeze out of a moline z for pulling?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top