(800) 853-2651
SHOP NOW

Recent content by johng143

Yesterday's Tractor Forums
  1. J

    spindle bushing removal

    This message is a reply to an archived post by soundguy on March 22, 2012 at 18:13:23. The original subject was Re: spindle bushing removal. You could use the tool made for the job, and have an easy time of it. See: www.gotschallbrandtools.com
  2. J

    Spindle & Kingpin bushing tools where to get them

    The spindle bushing tools have moved from ebay to www.gotschallbrandtools.com
  3. J

    What camp are you in?

    I am in the Love my 1943 2n camp. Dont care if it is stock or gorgeous, I just do the best I can for her sake. Such a sweetie pie. jg
  4. J

    Spindle & Kingpin bushing tools where to get them

    I am making and selling a tool for the spindle bushings, and another for the kingpin bushing on Ebay. The ebay url keeps changing so just search the ebay site for "Ford tractor spindle bushing tool". Its like my 2n, cheap, indestructable, simple, strong.
  5. J

    OT Anyone want to help with a home wiring problem ?

    So likely that in changing this equipment into the "fixed" mode, a couple of things will have changed. first and most important the safety (chassis) ground circuit pathway from the stove body all the way back to the breaker panel and then out to the stake in the ground will be intact, and...
  6. J

    Front Axle bushing replacement

    I am just finishing King pin, bushing, and axle replacement on my 1943 2n. I knew there was too much play in the front axle pivot, it rattled around while driving. In my case I had to remove the bracket from the front of the engine with the axle and King pin in it and drive the pin out with...
  7. J

    mystery hydraulic cover controls

    Thanks for your response and the hydraulic diagram. I think the diagram varies from mine because I have (apparently) the diverter valve and (i think) no position control. certainly there is no position control lever. it's beginning to appear that I either have a pump problem or a stuck...
  8. J

    mystery hydraulic cover controls

    well, it's a problem that the lift goes up and down, but will not rise with a load on it (me standing on the drawbar). it hasn't the power to lift 235lbs. if I step on it while it is rising, it stalls and stays put. i can feel slight throbbing through my feet. if i get off it continues on...
  9. J

    mystery hydraulic cover controls

    oh, this probably means that I ought not try to remove that right side inspection cover without taking the top off first? I wonder how I can get to the safety relief valve to replace it without taking off the right side cover? so many questions.... jg
  10. J

    mystery hydraulic cover controls

    The bracket holds a seat support that is hinged in front of the seat, the rear of the seat is held up by what looks like a mototrcycle rear strut (large spring coiled around a shock absorber). The more forward of the two knobs stops the lift mech wherever it is at present. If I use this knob...
  11. J

    mystery hydraulic cover controls

    I just bought this 2n. My first ever tractor. there are two controls on the right side of the hydraulic cover. Does anybody know what these are for? thanks
  12. J

    '45 2N hard start

    I just bought a non-running 2n. It had a poorly done 12volt conversion. Once I fixed the wiring, cleaned out the fuel system and confirmed spark at each plug, it still would not start. In desperation, I shorted the resistor with an alligator clip wire from radio shack, and Vroom!. That thing...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top