(800) 853-2651
SHOP NOW

Recent content by johninmn

Yesterday's Tractor Forums
  1. J

    Farmall M Cyl Head New vs. Remanufactured

    Just curious where in MN you are? There are a few scrap yards around and should have some used heads laying around for less if money is tight in class.
  2. J

    Intermittent fire on my 450

    #1 why did you replace everything if it was running good before? #2 put old parts back on one by one and see which one is bad. #3 throw bad parts away and enjoy.
  3. J

    M - Pulled the Cylinder Head...

    I just had my m head through the machine shop. Pressure tested fluxed and milled was $180. Now remember thats not having any valves ground or parts replaced
  4. J

    Axle housing gasket farmall m

    Right rear axle gasket started leaking on my m out of the blue. Never leaked before now i probably lost a quart in a week or so. Bolts are all tight. What gives? How big of a job is it to replace the gasket?
  5. J

    Halloween

    My kids Halloween costume. All credit to my wife who surprisingly isnt a deere fan.
  6. J

    German 310 diesel transplant

    Anybody ever transplant a 310 german out of a 715 combine into a tractor? Dads got one and the combine is pretty wore out but the motor still runs like new. Be a sgame to scrap it. I was thinking a 560 would be a good candidate for the motor but i havent done any measuring or figuring...
  7. J

    Access panel in h/m grille

    Whats it for? Why was it removeable? Im talking about the small piece towards the bottom of tbe grille
  8. J

    timing

    Now i must know, what is the twiwted belt method?
  9. J

    Milky oil in the m

    Checked engine oil today and its milky. I ran it till warm and saw no bubbles in the radiator. My question is since its been sitting the better part of the summer could it have accumulated enough condensation in the block to turn it milky or, as i suspect does it need a head gasket and...
  10. J

    Rotary Mower for a Farmall M - question about size to use

    I pull a 5 foot behind mine and you barely even know its back there. Pull type not a 3 point i like not having to adjust the top link
  11. J

    Farmall m tranny whine

    Forgot to mention that i did put new bearings in as well. Nothing else changed though
  12. J

    Farmall m tranny whine

    I put a new 5th and 4th sliding gear and shaft in my m because it would pop out of 5th gear. Everything works fine but the whine when its under load is considerably louder. In all gears not just 5th or 4th. I refilled with all new 80-90. Is it normal for these to have to wear in so to speak or...
  13. J

    Brush mower shear pin

    Yes there is a snap ring to keep tbe shaft on
  14. J

    Farmall m 2 way hydraulic valve

    Exactly like the one in the picture below. Thanks all
  15. J

    Farmall m 2 way hydraulic valve

    Yeah, i have. Thats why I'm asking here. I just wanted a picture of thr linkage for the 2 way valce so i can try to rig something up on mine
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top