(800) 853-2651
SHOP NOW

Recent content by Johnredpwr

Yesterday's Tractor Forums
  1. J

    d-6 tracks

    thanks I think I have it figured out.first thing I need to do is search ebay for a 9u Manuel.
  2. J

    d-6 tracks

    I guess photobucket img codes do not work here that was a first on any forum I have been on.
  3. J

    d-6 tracks

    What is the procedure of tightening the tracks as in how much to tighten them and is there a way of measuring them so both sides are even.they are sagging pretty bad.
  4. J

    temp gauge

    I put a new one in it and this crawler has been sitting for more then 10 years.I think something is plugged with rust or mineral deposits.We are going to try using air pressure next trip up there.
  5. J

    temp gauge

    D6 temp gauge was not working so I pulled it out and found there was no water in the jacket on the side of the block.Is there a special way of un clogging it ?
  6. J

    question on starting a d-6 dozer

    I did just that but for some dumb reason I put the pinion engagement lever back down after I engaged it. I was confused on how it worked but now I got it after a few youtube video's of people working on the internal parts. We have a cat grader with a pony motor on the dairy but we always pull...
  7. J

    D-6 pony belt

    The d6 all you have to do is remove the fire wall and its just a few bolts.
  8. J

    D-6 pony belt

    So one the that go's from the starter to the pony pulley in order to start the pony motor is called the Pony Governor Belt? or starter belt?
  9. J

    D-6 pony belt

    Yes I mean 9u how do I edit my post.
  10. J

    D-6 pony belt

    Would any body no what size belt for the pony motor on a Ru-d6.This dozer is not next to me I have an hour drive to the hills to work on it. I will appreciate any help John
  11. J

    question on starting a d-6 dozer

    Ok got it going owner came by and showed me the trick pony motor on idle when you engage the pinion then he revved the hell out of the pony then added the compression and it started.Now I know the trick of starting this dozer funny thing I had started it twice before then.
  12. J

    question on starting a d-6 dozer

    I think I might have had the pinion engagement lever down after I engaged it.I should have left it up .I will try and see if that was my problem and also not rev up the pony so much. Thanks for the replies
  13. J

    question on starting a d-6 dozer

    I am working on an ru-d6 that has been parked in the hills for 10 years.I did start it twice but found problems and had to fix them. Now for some reason I can not get the engine to start before it throws out the pinion gear. I did realize after the fact I have the pony motor revved up can that...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top