(800) 853-2651
SHOP NOW

Recent content by Jonathan8234

Yesterday's Tractor Forums
  1. J

    Need help identifying carb

    Yes this is a Solex. The numbers on the bowl are 31H618. Thanks again
  2. J

    Need help identifying carb

    Hello guys, I recently bought a lot of carbs at an auction and this one was in the pile. I believe it is for a 1250 gas but I'm not sure and can't seem to find any info online. It appears to be rebuilt and not used but I don't know that for sure. Can anyone confirm it is a 1250 carb and does it...
  3. J

    Model A belt pulley gear

    Thanks guys I have a big 2 jaw puller and a large split bearing puller as well hopefully those will get it off. How bad is it to get back on once it's off? I'm going to assume a press will be required.
  4. J

    Model A belt pulley gear

    I have a 1950 model A that I need to remove the belt pulley gear from. I have the belt pulley removed from the tractor already. Just looking for tips and tricks for getting the gear off and back on without doing any damage. Any info would be greatly appreciated thanks have a great day
  5. J

    1950 Model A piston identification

    Thank you Lynerd. I had a feeling they were from a 60 just wasn't sure had no idea they were LP pistons. I'm guessing with them being LP pistons the compression would be a little higher than stock gas. Would these have a higher compression ratio than just a standard aluminum high compression...
  6. J

    1950 Model A piston identification

    Hello all I have a 1950 model A that i need some help identifying what pistons it has. I have always just assumed it had aluminum high compression pistons just by how it runs and sounds. Well today I got curious and pulled the top engine cover and found a set of deere pistons that I do not...
  7. J

    UB distributor advance springs

    Hello guys, I am working on a Ub with a 1111718 delco distributor. The tractor ran well but I decided to just go thru the distributor anyways. Upon disassembly I found that the timing advance is froze up and both springs are no where to be found. Does anyone know of a source for these or...
  8. J

    MM cylinder jugs

    Thanks Vics I thought they were the same jugs but was worried the piston wrist pin might be a different diameter.Thanks again for your help
  9. J

    MM cylinder jugs

    Hello can anyone tell me if the jugs and pistons from a 504lp and a 336lp are the same. I'm trying to convert my UB over to a 336 and Moline parts are hard to find in my area.Im thinking the 504 was just a 336 with 2 more cylinders but I'm not sure. Any help is greatly appreciated. Thanks have a...
  10. J

    Putting a 403 in a UB Moline

    I will most likely just swap the parts from the 403 to my crankcase but if I use the 283 flywheel and put 403 starter ring gear on it looks like that might work I think the flywheel is the same diameter but the 403 ring gear has a bigger O.D. anyone ever went that route before sorry for all the...
  11. J

    Putting a 403 in a UB Moline

    Would you happen to know what is involved in the swap? Or a way to make it work
  12. J

    Putting a 403 in a UB Moline

    Hello I have a UB moline that I'm putting a 403 power unit motor in but I'm having trouble figuring out what flywheel I will have to use. I have been told use the 403 flywheel and starter and the UB clutch but I have also been told that the UB clutch may not work on the 403 flywheel. I have also...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top