-
J
B414 Gas Engine
I have a 1964 B414 tractor with a BC144 gas engine, I want to do a engine overhaul. Does anyone know where I can get the lowest priced gas In Engine Overhaul kit. I can find kits for diesels but can't hardly find anything for gas engines. Thanks- jown63
- Thread
- Replies: 1
- Forum: Farmall, International & McCormick
-
J
JD 630 moco height
If I remember right the further you screw your turnbuckle in the higher the head goes. So to lower your head you will have to unscrew your turnbuckle to lower your cut height.- jown63
- Post #1
- Forum: Implement Alley
-
J
JD 467 Round Baler
Hi all, I finally got around to putting up some more hay last week and Jim your right I love that baler. I had to get out of the tractor a few times when I was first setting it up to check bale density and stuff like that but after I checked that everything was set like I liked it I was able to...- jown63
- Post #1
- Forum: John Deere
-
J
JD 467 Round Baler
Thanks guys for the reply's, yeah I ran a lot of bales through my 435 but it had the old style monitor and the twine and wrap was hydraulic driven. I wasn't for sure about the electric actuators. The 467 springs look brand new just to look at them, one of them has a barcode sticker on it, it may...- jown63
- Post #1
- Forum: John Deere
-
J
JD 467 Round Baler
Hi Everyone, Well I came across a 467 Baler at a farm auction and I bought it. I knew the farmer who had it he bought it new and always kept it in a shed. He just put new chains on it last fall, it shows on the monitor that he baled just over 6400 bales. The belts look good they still have the...- jown63
- Thread
- Replies: 7
- Forum: John Deere
-
J
FORD 7710 LOADER VALVE
Hi I put the loader valve on the tractor today the plumbing took longer then I would of liked but that was mostly due to getting the right fittings, seems like you can have every fitting but the right one. but its on and hooked up. I mounted the valve midmount and ran the remote joystick into... -
J
FORD 7710 LOADER VALVE
Hi the valve that I'm go to use is a Prince 20 Series CCLS and I I've bought the shuttle valve for a 7740 and am hoping it will work, I haven't had a chance to install them yet. I didn't try Alexanders but I did just check out their site. Thanks -
J
FORD 7710 LOADER VALVE
Hi Rod thanks for the Reply, we couldn't find a shuttle valve for the TS90 but did find one for the 7740, do you think it would work? Your right about me not being worried about the plumbing part as long as it operates the valve alright. The thing that's worrying me is that it is about 1/4 the... -
J
FORD 7710 LOADER VALVE
Hi I'm putting a Loader valve on a 89 Ford 7710 tractor and I've got a CCLS Valve but I can't find the Shuttle TEE Valve for the sensing line, the number I have is NH 83954424, the dealership for my area says that they haven't got one and didn't know when they could get one that they are on... -
J
7710 Loader Valve
Hi RodInNS, I have another question for you will a PRINCE 20 SERIES VALVE W/LOAD SENSE DA CYL work. If so Surplus Center has it Item Number: 9-20-2-LS. They have 3 different choices, one with "spring center" another with "Detented Section" and the last is with "Float Section". I'm not sure which... -
J
7710 Loader Valve
Hi there, I have a 7710 tractor that I"ve had for quite a while and I love it but the loader works off the tractors remotes. It only has 2 sets of remotes so when I have to hook up to something I have to rob a set of remotes from the loader. I"d like to hook up a spare loader valve I have for... -
J
Loader Valve
This is the CC plug that came with it and it's what it shows it takes when I replaced the O-rings I mic'ed it and it seemed to measure out right and when I screwed it in you can feel the resistance when the O-ring starts in and it feels right.- jown63
- Post #1
- Forum: John Deere
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy