Recent content by jshwhite

  1. J

    MF 65 diesel running rough, low power, black smoke under load

    I ordered a replacement element from Steiner tractor. Waiting on that to arrive. In the meantime, I hose clamp to double layer t-shirt over the intake and took it out for a spin. The black smoke/power may be marginally improved but not much. As mentioned in my original post, the black...
  2. J

    MF 65 diesel running rough, low power, black smoke under load

    Pulled the air cleaner out to check it this morning. The "steel wool" filter element is in bad shape. I don't see any way to pull the canister apart to replace the filter element. Can't find any replacement canisters online either. You'd think they'd make something aftermarket. Any suggestions?
  3. J

    MF 65 diesel running rough, low power, black smoke under load

    The air cleaner looked ok, but I'll tear it down and check everything. How's the best way to clean these oil bath filters? I'm not convinced that is connected to it running rough after replacing inj pump and injectors. 🤔
  4. J

    MF 65 diesel running rough, low power, black smoke under load

    Ha! True. But usually that's accompanied by more power, not less 🙂
  5. J

    MF 65 diesel running rough, low power, black smoke under load

    Hoping for some help solving this issue. I have a later model MF65 diesel AD4-203. It ran great and had good power when I first got it, but with quite a bit of blow-by. The injection pump was leaking, so I sent that and the injectors to Mike at pumpguys. The pump was unrepairable. So I got a...
  6. J

    Adding rear remote to MF 65

    Thank you! That's just the info I was needing. So this one should be pressurized when the 3pt lever is "raised"?
  7. J

    Adding rear remote to MF 65

    I just picked up a MF 65 diesel that I'd like to use for brush hogging. My brush hog has a lift cylinder, but I don't have a remote on the tractor. I'm fairly mechanical, but a bit novice on hydraulics. I'm trying to figure out the cheapest way of adding it a way to raise/lower the brush...
  8. J

    Continental gas engine identification and rear seal leak

    I got the seal and just wanted to get opinions on installing it. It's about 4" diameter and I don't have any seal installers or sockets big enough. The seal is held in place by the crank bearing, so when I unbolted the bottom half of the crank bearing, the bottom half of the seal was loose...
  9. J

    Continental gas engine identification and rear seal leak

    Well we're making progress - on both the seal and the engine identification. I pulled the flywheel, dropped the oil pan, and took the crank bearing off to get the seal out. The seal had several numbers on it. I took it to a couple of really good parts places but unfortunately all the...
  10. J

    Continental gas engine identification and rear seal leak

    Yes, there is a flat spot there, but if it had a plate on it at one point it's gone now. I cleaned it pretty well and can't see any numbers stamped into it. Here's a pic. There are some numbers cast into the block to the left of it but they're near impossible to read. Looks like "2000" is part...
  11. J

    Continental gas engine identification and rear seal leak

    Yeah this one will run itself dry. It's a fast drip -almost a stream - when it's hot. Regarding replacing the seal, can I pull it from the rear or do I have to drop the oil pan?
  12. J

    Continental gas engine identification and rear seal leak

    Alright, here's a couple of pictures.
  13. J

    Continental gas engine identification and rear seal leak

    Ah, ok, that explains it. Thanks! Will try to either get permission or rack up a few posts and then put a couple of pictures here. Yes, it is a 4 cylinder. Valve cover and intake are yellow, rest of it is red. I've looked over it quite a bit but can't find any data plate. Will do some more...
  14. J

    Continental gas engine identification and rear seal leak

    I can't get the system to let me attach a picture. It's telling me it's spam. ??
  15. J

    Continental gas engine identification and rear seal leak

    New member here, but I've been around for a while reading the forum. Always appreciate the help and info. I've acquired an old Morbark/Beever chipper powered by what a friend told me is a continental engine. Looks to me like it came off a tractor (the chipper engine was replaced at one...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top