(800) 853-2651
SHOP NOW

Recent content by jt4541

Yesterday's Tractor Forums
  1. H

    mw 1500

    Can anyone tell me which mode krone round baler are the same as a M &w 1500 round baler? I'm looking for parts for my M & W and think I have found them via krone but want to be sure...
  2. J

    1958 861 Powermaster Starting problems

    got in running..points needed cleaned.
  3. J

    1958 861 Powermaster Starting problems

    1958 861 powermaster. went to crank her up today for the first time in several months...plenty of juice in the battery..turned over, but didnt start. definitely getting fuel and air to the carb. i feel like its not getting any fire. i used a basic tester to check, im getting juice through the...
  4. J

    861 Powermaster starter problems

    local business. i took it back to them. they checked it out and said everything was good. somethings not right though
  5. J

    861 Powermaster starter problems

    ok. ive never done that. any special tools involved? thats just held on by a pin right?
  6. J

    861 Powermaster starter problems

    ring gear looks good. should replace starter drive or just buy new starter?
  7. J

    861 Powermaster starter problems

    had starter rebuilt, now it will not engage flywheel. i can hear the starter spinning. any ideas? or suggestions? thanks
    • jt4541
    • Thread
    • Replies: 7
    • Forum: Ford
  8. J

    861 Ford Powermaster

    I found a local guy to rebuild my starter. Saving me about 150. appreciate it
  9. J

    861 Ford Powermaster

    Thanks for the reply. Looks like I need a new starter.
  10. J

    861 Ford Powermaster

    1958 Ford 861 Power master. Started engine for approx a minute or two to bleed hydraulic pump. Starter button stuck on while tractor was running. The starter isn't engaging now. New battery, just replaced solenoid. I also tried to jump start. Solenoid is just clicking not engaging starter. I...
  11. J

    861 powermaster hydraulics

    hello..i had an earlier post about the hydraulics on my 1958 powermaster. i primed the pump and now seems to be working fine. i just have one question. when the touch control lever is all the way up, the lift arms stop about 6 in before they are all the way up. is this a control valve problem...
    • jt4541
    • Thread
    • Replies: 1
    • Forum: Ford
  12. J

    861 powermaster hydraulics

    it was a 3/8" fitting. i got the pump primed and the hydraulics are working. kinda slow to respond to the control lever and maybe not lifting as high as it should.
  13. J

    861 powermaster hydraulics

    primed the pump. it was a 3/8" fitting. the lift is working , but seems slow to respond to the touch control lever and maybe not lifting as high as it should. thanks for the help. im gonna take the lift cover off when the weather warms and check it out
  14. J

    861 powermaster hydraulics

    thanks for the help. i got a 3/8 barb fitting and some clear hose im gonna try. i never even thought about your way
  15. J

    861 powermaster hydraulics

    im gonna try the 3/8. if that doesnt work il try the other way. il let you know when i try it tomorrow
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top