(800) 853-2651
SHOP NOW

Recent content by Jthomas1970

Yesterday's Tractor Forums
  1. J

    Starter drive mistake

    I agree, just install it and start the engine. It will take care of itself.
  2. J

    Case 310G dozer hydraulic problems

    Picked up the pump and cylinder from the repair shop yesterday. Installed it all this morning and other than a small leak at the controls, everything is working great! Was the pump all along, Thanks everyone for all the help and support, it's truly appreciated! Jonathan
  3. J

    Case 310G dozer hydraulic problems

    The repair shop still has the pump and one lift cylinder. They are replacing the shaft on the cylinder. It appears to be the pump bypassing internally. I should be getting both back any day now. I feel pretty good that the problem was the pump but won't know for sure until I get it back and...
  4. J

    Case 310G dozer hydraulic problems

    Would appear that the pump is the problem. The repair shop has tried to find another pump, as did I with no success. They are currently machining some of the parts and hoping for the best. They do believe that they can get it working again. I will know for sure once they complete the process...
  5. J

    Case 310G dozer hydraulic problems

    Thank you. Has taken a few years off and on to get it to where it is now. Never dreamed that the hydraulics would cause this much trouble. The splines on pump and pulley are fine and working. Still waiting on pump repair. Hope that is the problem. I'm looking forward to running it.
  6. J

    Case 310G dozer hydraulic problems

    Bleed orifice is clear and filter is clean. I will remove the o rings and see if I can replace them. Have not heard back about my pump as yet. Thanks.
  7. J

    Case 310G dozer hydraulic problems

    A big thank you for all that responded with suggestions and help. I finally got the adaptor I needed to check the pump pressure. Barely any pressure! I have now drained the fluid out, taken the pump off, and will be taking it into a local hydraulic repair shop for evaluation this morning. I...
  8. J

    Case 310G dozer hydraulic problems

    Thanks for the suggestion. I have already taken this valve out and cleaned it. Minimal debris in it and all appeared good. I left the adjustment as it was and did not try to adjust it. Thought I would check pump pressure first. I ordered a pressure gauge kit but haven't had the time to...
  9. J

    Case 310G dozer hydraulic problems

    What are you referring to when you talk about the Float mechanism? I don't see it in my manual.
  10. J

    Case 310G dozer hydraulic problems

    Thanks for all the suggestions. The filler port is very small, but I will try and look inside. I haven't done that yet. I left the same setting on the relief valve when I cleaned it. I haven't tried to adjust it as yet. That maybe worth a try. I ordered a pressure gauge set last night...
  11. J

    Case 310G dozer hydraulic problems

    Have the general shop manual for the 310-350 machines. I'm almost 100% sure I have everything hooked up correctly. Pump is shaft driven from front engine pulley and it is turning. Only thing I can think of now is an internal problem in either the pump or valve control box. Thinking of...
  12. J

    Case 310G dozer hydraulic problems

    I don't think I have a diversion valve. I have the manual, but it doesn't say anything about a diversion valve. I do have a Main Check valve located in the control box. I pulled it out according to the manual, but it looked fine. I cleaned it and reinstalled, but the dozer does exactly the...
  13. J

    Case 310G dozer hydraulic problems

    Yes, all new fluid and full.
  14. J

    Case 310G dozer hydraulic problems

    Hi guys. I'm looking for some help with a direction I should go. I have been restoring a Case 310G dozer with six way blade. Hydraulics all worked when it was taken apart a few years ago. Now finishing it up with new hoses, filters, and fittings etc. Same pump and controls. Appears to be...
  15. J

    JB Weld

    JB Weld makes a special fuel tank repair product. I have used it with with more success than the regular JB Weld.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top