(800) 853-2651
SHOP NOW

Recent content by jturn36178

Yesterday's Tractor Forums
  1. J

    Chevy C 60 pto hydraulic pump seal replacement

    In order for someone to comment they need to know more information: What is the pump mfg. i.e. cessna, or some brand, What is the pump model number. If possible what is the pump serial number. With this info many can give you advice. Good Luck, Jim
  2. J

    mf 135 air cleaner

    Yes, it may require cutting a few spot welds. The filling screen material is available in lots of places. Once the screen and holding piece is re-installed, (if I remember correctly the bottom oil container will prevent them from coming down Good Luck Jim
  3. J

    Massey 283 Front driven Hydraulic pump

    the front pulley has to be changed to one with bolt holes to allow the attachment of a coupling. the coupling usually has rubber flex holes to bolt it to pulley, then a shaft will go into the coupling and extend out through the pivot pin to a pump mounted out in front of the front housing...
  4. J

    Save that hi lift jack

    Thanks again
  5. J

    Save that hi lift jack

    Where would I order a "pin kit"?? Thanks Jim
  6. J

    MF65 transmission shaft retainer housing removal

    My best advice is to go to You tube and watch Bundy Bears Shed and watch. MF 135 6 speed transmission #49 stripping the gear box. (<Even though this video is for a 135 it is the same process on a 65 etc.) p>There is a gear that protrudes into the upper input shafts housing that must be dropped...
  7. J

    MF65 transmission shaft retainer housing removal

    I'm surprised someone hasn't replied to your question. You are correct to not pry on that. It has been many years since I have removed that. I will have to go home to find my repair manual in order to be confident in my advice. A repair manual would be a great investment for you. I'll get...
  8. J

    synthetic oil?

    Ive work for an oil company for several decades. There are MANY complications that involve fitting into two classifications: So i'll try to make it simple; I'll preface with "base oil" is the lighter viscosity component that is usually "dinosaur/plant based" petroleum. Commonly called...
  9. J

    Life expectancy of Kawasaki liquid cooled engine

    I just replaced an entire engine on a Kawasaki mule. I forget the engine number. The reason I replaced is because the previous owner had torn several holes in the air filter connecting hose and ran for how many years???? Anyway, is smoked pretty bad. That motor has well over 900 hours on it...
  10. J

    MS 85-Engine Continental HD 277 HELP!

    Those engines were made for gasoline and converted to diesel. the heads would crack and cause the same symptoms. Good Luck Jim
  11. J

    Z134 Timing

    Just do a search for 35 ferg or to35 ferg or 50 ferg timing. There are several. Remember: if the advance in bottom of dist. is weak or worn. You won't be able to use the suggested lowers settings. I think last time I timed my to 35 was at 800 rpm an 11-13 degrees BTC
  12. J

    Bush Hog Stump Jumper help

    I have driven wooden wedges between the deck and the jumper. Use as many as two or more evenly spaced. When you got them drove in tight. then smack shaft with a hammer on a piece of oak or hard plastic. If it loosens but doesn't come all way off. Just add more wedges. Good Luck. Jim
  13. J

    Bush Hog Squealer 48

    Bush hog blade bolt kits are common item, so should be ok to drive them out. Like the man said, be sure to support the blade holder when driving out you can risk busting the bottom of gearbox if not supported. You can try to heat the blade holder with an acetylene torch and that would make them...
  14. J

    draw bar

    It appears to be off some kind of implement. Not sure what??? Almost looks like it would fit as a stabilizer bar from under the fender bracket to the three point lift arm pin on an implement??? Just a guess. It is not thick enough to stand the kind of weight that the swinging drawbar...
  15. J

    Explain draft control

    Ok, if and that's a big if, all the associated internal linkages are adjusted properly: The draft control is created to sense the pull on the top link and raise or lower the lift arms accordingly. That is the simple explaination. It's main use was for molboard plowing. But could be used with...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top