Recent content by jwb53

  1. J

    Ford Jubilee Hydraulics

    Thanks for that thought. I should be able to find it with some research, but perhaps you would be so kind to point me in the direction of where the unloader valve is located on the Jubilee? Cheers.
  2. J

    Ford Jubilee Hydraulics

    Hello Ford Fans. I have a 1953 Ford Golden Jubilee that my Dad bought used when I was around 7 years old. Back sometime in the 60's Dad put a Ford 2000 hydraulic pump on it so that it would better lift the JD 494A planter we were pulling behind it. (Our 'big tractor at the time was a...
  3. J

    Cleaning old tractor gas tank

    Steve@Advance. Excellent tip! I hadn't even considered there would be new aftermarket replacement gas tanks out there for the TO-20. There were actually multiple sources. I went with the YT Parts Store. I would quickly have overrun the cost of the new tank in time, materials, and "despair"...
  4. J

    Cleaning old tractor gas tank

    Today's subject: Old tractor gas tanks. In particular, one on a Ferguson TO-20. It is what could be best described as "yucky" on the inside from what I can see. The radiator shop where I used to get them boiled out has stopped doing that service. Now I am wondering what might be my best...
  5. kcm.MN

    Tuesday Truck Pic

    1967 Autocar
  6. S

    A Starter Problem

    Folks, I'm having a starter problem on my 8N. At times when engaging the starter it won't engage and I'll hear it just spinning. Also, sometimes it will engage and start to crank the engine, then will drop out and just spin. This is happening more and more often. Do I need to replace...
  7. J

    MF 1100 brake issue

    All good things to try once I get it home, but won't be able to do that when I go to pick it up... And I doubt I could get the current owner to do all that before I get there. Yes, early CDW serial number. I'll give you a call when I get a chance.
  8. J

    MF 1100 brake issue

    Hello. I have purchased a very early serial number MF 1100 tractor. It reportedly has one brake which is "dragging heavily"... The current owner spoke with his local dealer, who suggested "disconnecting and plugging a line" to make moving the tractor around less difficult until the brakes...
  9. J

    Farmall H rough running

    Yes, another good idea. Had that problem on one of the small engines on the sprayer support trailer this summer. It would start cutting out and eventually die. Loosening the cap fixed it right up. It will be easy enough to loosen or remove the gas cap next time I have it running to check for...
  10. J

    Farmall H rough running

    Thanks for the quick responses. It does have new gas and clean sediment bowl. Choking it a little (or a lot) hasn't helped. I have not tried to isolate by pulling plug wires. I have not wiggled the distributor shaft. Good ideas. I have also thought about the condenser. I remember when I...
  11. J

    Farmall H rough running

    Hello Farmall guys! I have a 1950 Farmall H tractor - the only Farmall in my collection. It only gets started and moved around once or twice per year. It starts fine, and runs well initially, but after it warms up, it starts running rough, almost like it is missing out, but not consistent...
  12. J

    Cost to haul tractor to Fort Worth, TX

    Thanks for your reply. $1.50 to $2.00 per loaded mile seems fairly consistent.
  13. J

    Cost to haul tractor to Fort Worth, TX

    Hey you antique tractor haulers. What would it cost to haul a Massey-Harris Challenger (around 4,000 lbs) and some parts (wheels, carb, small parts) from Indianapolis, IN to Fort Worth, Texas? About 960 miles one way. Thanks!!
  14. J

    Ford Jubilee PTO Shaft Seal

    I have been able to isolate the source of the "seep". Not the seal at all. It is actually coming from between the PTO shaft and the interference-fit sleeve... Damn the luck. The seal seems to be leak-free. Current plan is to drain the differential housing, pull the PTO shaft back out, clean...
  15. J

    Ford Jubilee PTO Shaft Seal

    Thanks for the input guys. Glad that I at least installed it right side in. I looked the new sleeve over very carefully and didn't find any burrs or bad spots, and of course oiled the seal before sliding it over the shaft. I wondered about running the PTO for awhile to see if maybe it has to...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top