Recent content by KC Colorado

  1. N

    Ford 5000 pinging and dieseling

    Hello all, I have a ford 5000 gas job I recently aquired Having an issue of pinging at medium to high throttle or a moderate load, I can make this go away by adjusting the distributor timing. However when I adjust this the tractor will not shut off, just keeps knocking and pinging along. I have...
  2. Dan in Ohio

    Spraying corn stubble

    What are farmers spraying on corn stubble at this time of year?. Not that I mind but do not think I have ever seen this in December.
  3. RedMF40

    9N magneto question

    Hello All, Looks like the 1941 9N I picked up recently with stuck motor has magneto ignition. Is there anything I should know about this system as far as maintenance or fix-ability? I've done a little searching on the net but mostly have found vendors with parts for sale, and not much in the...
  4. C

    Shed shots for Ande

    Dan, you spoke of shed shots,, a few from part of the big shed here, Please look past the mess, cnt
  5. C

    govenor warped

    I've run into several leaking governors. If you take it off an put the housing on a flat surface it has a slight bow up in the middle. I know of no way to straighten it other than face grinding it. I've been using Dow 732 to form the gasket needed. This to common problem and must be a reason...
  6. DPittman

    Finally got here

    We're getting the ice here in central I'll. Just started a few hours ago. How bad is it where you're at?
  7. E

    posting pics.

    Hi, I am a real neophyte with computer stuff. I would like to post some photos of my tractors etc. Some of my orchard and sites from around here. I was wondering if you have to put the photos into a certain pkg then send, or can you just select from your storage like you would attach to an...
  8. N

    Ford 5000 Simms Minimec control

    Hi, My first post ever. Helping a widow sell a 1969 Ford 5000 (4 cyl diesel, Simms Injection, about 3,000 hours) that had been parked 4 years out back in a shed. Did several inspections and it started right up. Needed battery charge and jump. Ran 10 seconds probably on fuel in pump...
  9. R

    early 3020 PS vs late 3020

    I know the late model side console powershifts are most valuable, but what about early 3020 with the powershifts? Are they worth more than the synchros? What are some of the red flags in evaluating condition of an early 3020 ps? I found one that seems priced well below norm, because they say...
  10. Thomas(AB)

    Opinions....Oliver 1365

    Neighbours looking at a Oliver 1365, 3pt hitch doesn't work, besides having that fixed, anything to watch out for on these tractors? It's going to be lightly used for a acreage. Looks just perfect size for the job.
  11. C

    756D PTO

    756D w/dual PTO/ The PTO will not engage from a cold start without significant engine speed--then engages suddenly and fully resulting in a sudden forceful "jerk." After the PTO has been used awhile it engages normally. Also, driving along at perhaps half speed or more, with the lever in the...
  12. D

    New Holland 474 haybine ?

    Looking at a 474 haybine. SN 625739. what year model is this and how reliable are these machines. I have a 472 that is well used. What are the major differences in the two machines? thanks
  13. Charles in Aus.

    Chainsaw Gremlin update

    Thanks to all that offered help :) New fuel can , new fuel , and a thorough clean out of each carburetor and all is well . I was overly attached to the little ex Australian Army fuel can I have used for the last thirty years . It has served me and my Country well and has now earned its...
  14. F

    Operation Meter (Tach/Hour) Retrofit

    General question, has anyone retrofitted the Operation Meter to a Series I D17. I have a 1959 serial #25529 Diesel that does not have the Operation Meter. I have the shop and parts manual showing all of the parts, but not the where the engine side pieces attach. Mine is the one with the power...
  15. J

    Model 70 Powershaft Clutch Assembly

    Take a look at the diagram below. Note the oil seal (Key 8) and the clutch housing (Key 23). The oil seal is leaking and a small amount of 140W transmission oil is mixing with the 10W PTO oil. The oil seal is being replaced. Take a look at the diagram below. Note the powershaft (Key...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top