(800) 853-2651
SHOP NOW

Recent content by kc94507

Yesterday's Tractor Forums
  1. K

    Trumpet Gaskets Soak in Water?

    Do I let the gasket dry or put on wet? If its wet will the permit me to still use the Permatex Ultra Copper Gasket Maker or the Indian Head Shellac?
  2. K

    Trumpet Gaskets Soak in Water?

    I am about to reinstall my trupmets on the Ford 9N. The gaskets are paper. Do I soak these in water to get them to fit? If so do I still use some Indian Head Gasket Shellac or a permatex Ultra Copper Gasket Maker? Not sure... Help is appreciated.
  3. K

    Diffential Install Difficulty Ford 9N

    After installing new bearings and cones on the differential and the trumpets I am having trouble installing the differential. I have lifted and slid the differential onto the right wheel drive Shaft (obviously I have the left trumpet off). I cannot get it to push or slide onto the splines...
  4. K

    Leaking Lower Lift Bolt 9N

    I have a 1941 9N that has the smaller 7/16-20 bolts that go through the lower lift point plate bracket. The Hydraulic /Transmission oil is leaking through the bolt (not the lift point stud). I will replace one of the bolts and tighten it and put a new gasket on the outside of it. What...
  5. K

    Draft Control Spring Plate Question

    Here is a picture of the old draft control plate.
  6. K

    Draft Control Spring Plate Question

    I have a 1941 9N with a draft control plate that has an oblong hole. I ordered a new plate and the one that was shipped to me was for an 8N. It has a pin on the plate. The pin interferes with the plunger. When I look at my worn 9N control plate it has a round section that is bored out about an...
  7. K

    Head Bolt Leaking 1948 8N

    Thanks so much!! I will try it. Really appreciate the advise.
  8. K

    Head Bolt Leaking 1948 8N

    I have one of the head bolts on my 1948 8N that are in the center of the head (holds the bracket to the carburetor) that I removed in my restoration process. I reinstalled the bolt. It is now leaking cooling fluid. I tried putting some "Aviation Form A Gasket" on the threads and it did not stop...
  9. K

    Metal Shavings in Hydrolic Oil

    It is a 1941 Ford 9N
  10. K

    Metal Shavings in Hydrolic Oil

    HI Guys: I just got may tractor put together and it started just great (3 months of restoring). I changed the transmission/hydraulic oil today and here's what i found. The differential oil looked very clean (kid of pink like) as it drained out the small plug closest to the PTO. I then pulled...
  11. K

    Cylinder Head Bolt Leaking Radiator Fluid

    I put the bolt back in with Aviation Form A Gasket #3 which is good for temperatures up to 400 F.I gooped the fluid all around the lower threads of the bolt and sort of dripped a bunch in the hole just before inserting the bolt. I notice that the bolt sort of drops in the hole and then starts...
  12. K

    Cylinder Head Bolt Leaking Radiator Fluid

    Correct.... Threads in block (my miscommunication) . Can there be other leaking issues?
  13. K

    Cylinder Head Bolt Leaking Radiator Fluid

    Are there any worries that fluid is leaking into other areas of the head/pistons/oil pan? Thanks
  14. K

    Cylinder Head Bolt Leaking Radiator Fluid

    Oops forgot to upload the picture. Help KC94507
  15. K

    Cylinder Head Bolt Leaking Radiator Fluid

    Help!! I have the middle bolt in the Cylinder Head of my 8N engine leaking radiator fluid. Recently I had tried to remove a bracket on the carbureator linkage that was held on by a Cylinder Head Bolt. When I removed the head bolt it was worn at the threads and almost looked cross threaded. I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top