-
K
Ford 3000 or 2000
The only other numbers on the engine are HH2 5806. Thanks again for all the info. -
K
Ford 3000 or 2000
Got the block #'s today they are as follows: Engine: E2 NN 6015 BY Tranny: C5 NN 7006 By Rear End: C5 NN 4024 U It definitely looks like the engine was swapped out as the casting numbers are not even close. I do not know what the numbers mean. Hopefully some one can tell me. The tractor only... -
K
Ford 3000 or 2000
Thanks Phil, but I really do not want a select o speed tranny. -
K
Ford 3000 or 2000
I know this tractor has the adjustable link on the left side. It is sounding like it is a mutt for sure. But that is okay. -
K
Ford 3000 or 2000
Thanks for the info will check on the block and injection pump tomorrow. Sound, yeah it does pretty much all I want just curious about the tractor. I want a larger tractor and will probably get a 4000 soon. -
K
Ford 3000 or 2000
Just got to looking at the serial numbers on the tractor today while doing some maintenance and they are as follows:B1023C 8H21B C214149. Which should translate into a 2000 Ag All purpose with a gas engine and a live 540 8 spd tranny, made in August 21 1968 in the USA and the remainder being... -
K
Couple Ford's working
Just a few pics of my dad and I raking and baling some clover and grass. -
K
High School, College, and Graduation Requirements
Lanse, I know I am a little late to this thread, but if you read this I would like to say as someone that can weld and fit and has a degree, you can always weld and I still do in my shop when necessary. But with my degree I can still provide for my family since I got hurt. I am not able to... -
K
Mitering Pipe
If you can get The Pipe Fitters Blue Book by W.V. Graves. It has all the necessary measurements for those cuts. Until then here is the page from the book with the measurements that you will need for the 22.5 deg cuts. -
K
O/T good morning folks
Well it was 42 degrees and foggy in SE Mississippi this morning. Ready for some colder weather to slow down the mosquitoes.- Keb in MS
- Post #1
- Forum: Tractor & Farm Talk
-
K
who engineers this stuff????
dave2 I will confess I am an engineer and I get so frustrated trying to tell people that the designs they have will be impossible to install or work on. I guess growing up on a farm and always working on equipment I try to find the best and quickest way to get something repaired. As it has...- Keb in MS
- Post #1
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy