(800) 853-2651
SHOP NOW

Recent content by Keith '44 2N

Yesterday's Tractor Forums
  1. K

    Massey Ferguson 35 Deluxe Tach and rear pin?

    We have a mid to late 50's Massey Ferguson 35 Deluxe. I was wondering if any one restores the original tachs or could provide information if I wanted to do it myself. Also, the long pin that goes thru the 3 casting holes at the top of the rear casting, used for hooking brush mower check chains...
  2. K

    Mount Ford 19-97 loader to 1958 MF35

    Ptfarmer, are you trying to show me that these brackets are available for sale still? If so, I just realized this. Where are these parts pages copied from? I was trying to find it on the web so I can inquire about them. Thanks, Keith
  3. K

    Mount Ford 19-97 loader to 1958 MF35

    Thanks for all the info!
  4. K

    Mount Ford 19-97 loader to 1958 MF35

    We have a 1958 MF35 and would like to mount a Ford loader model 19-97 to. Does anyone know what front mounting plate is required, or better yet have one available to sell to us. I have the rear mount and assume they are the same whether you mount to Ford or Ferguson since the rear axles are so...
  5. K

    Ford 703 loader

    I want to put a quick attach adaptor onto my 703 loader. Does anyone know of a good source for one. Thanks
  6. K

    OT....Wife is in hospital

    God bless both of you Gary - I wish her a speedy recovery and pray she will get well soon. Keith & Gail
  7. K

    8N Split (Photos)

    Colin, I have a good used clutch disk and pressure plate sitting on my shelf i will sell cheap if you want to go that route. Thanks, Keith
  8. K

    Wrong part of the country

    Richard - I still have a complete front mount engine out of an Industrial power unit here in Maryland... I"ll let it go for $350, I just want it out of my garage. You figure out the shipping, maybe we can find someone making a run again like i missed out on earlier in the year. Doesn"t have to...
  9. K

    Another N?????

    Old, i got a good front mount engine if you are interested. It came out of a stationay engine that ran a cider press. I am in Md 21797. I'd sell it pretty cheap, and you could have a good working 8N. Keith
  10. K

    NEED...Rebuildable M/S TSX428 "JUBE" carb

    Gary, I can't help you with your need of a Jub carb, but i would like to get your info so i can have you rebuild 2 carbs for my 2N. Thanks, Keith
  11. K

    Hey GB in MT - how do

    you remove, or what is your method to remove the choke shaft and throttle shaft bushing on an original Marvel carb? Also - is is just one bushing each... just on the lever side? Thanks for the info. Keith
  12. K

    Installing a post on a starter

    I am rebuilding one for my 2N right now and it needed a post as well because the original was stripped. I took it apart and the best I could tell I had no solder, but I intended to solder the new in with regular solder because of the heat needed for silver could damage the windings insulation...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top