Recent content by KEITH GEORGE

  1. M

    460 brakes

    Should the balls have lubricate on them when reinstalling with new liners?
  2. B

    Looking for 4040 info

    Hello all, I am working on a book about my Dad. Call it a book about rediscovering who he was (he passed when I was 11) as I search for the JD 4040 he had. It was sold about a year after he died. For whatever reason, that was my favorite tractor to ride with him on when I was a kid. I...
  3. Geo-TH,In

    length of brake away cable and safety chains?

    After my dump trailer came off ball when it was dumping load got me to thinking, how long should my safety chains be? And when do you want brake away cable to apply 12v to electric brakes? I think the brake away cable should only work after safety chains fail, because applying 12v to my...
  4. 1

    case 580b skiploader hydro trans

    I am new to tractors my skipploader was running good -until it lost pulling and pushing power-it moves forward and up a 14% grade and all of a sudden it stops and goes backward.Any suggestions.I have changed all the filters and fluids.I lift the wheels off the ground -put in forward and it...
  5. R

    Hercules multifuel engine

    I'm hoping someone can tell me which SAE bell housing pattern I have on a Hercules multifuel engine out of a deuce and a half. I'm wanting to install this where an old R22 (U6501) Continental gas engine used to be. The transmission housing appears to be an SAE1 housing pattern, the...
  6. G

    hay wagon frame

    I am building a wooden floor for a wagon running gear, and am not sure how to secure the 4x4 cross members to the 2 frame members running length ways. Can anyone provide ideas? Thanks in advance
  7. J

    linde heliarc 250 hf tig w/ hw-26 torch

    is this tig torch water cooled or is it inert gas ? if welder is in NON heated garage will it cause problems? can you change h2o to propylene glycol (anti-freeze coolant auto) to prevent freezing. thanks
  8. B

    8n Oil Pressure

    I'm only getting about 10psi at start up on my 8n on a rebuilt engine. First I had issues with low compression and the issue ended up being that the crankshaft was not timed properly with the camshaft, some good fellas from the forum helped me figure that out. Looking around this site today...
  9. R

    What kind of bug leaves purple splatter?

    Just curious what kind of bug leaves this purple splatter? Doesn't come off white vinyl siding.
  10. D

    Torque-Long

    Folks, I invite those of you who are not railroad buffs or interested in things mechanical to skip this video as it is long and of interest to a limited audience. Those who chose to at least give it a try may want to fast forward to around 5:00 if you are not interested in steam locomotive...
  11. Steve in IL

    Used tires and rims for White 2-105

    The 34" tires and rims (power adjust) on my 2-105 are getting very tired. Any suggestions for good places to look for replacements? Most salvage yards with Whites seem to be in Wisconsin or Iowa. Also, any suggestion on perhaps what other tractor model rims might fit? Thanks.
  12. R

    Re: 1994 F250 diesel brake problem

    Hobo, lots of places the filter bowl can leak. I'm assuming when you had it apart you replaced all of the short pieces of rubber fuel line that go to/from the bowl? Also the transfer pump has a deep hole in it right above the valley where it is mounted. That one will fill up the valley...
  13. F

    Draft control

    Hello I got a ford 900 and I was wondering if anyone else has had the same problem as me. When I plow in draft control I have no control over the depth of the plow. The only thing that stops it from going deeper in the cutler hub, I'm thinking something in the draft control spring is rusted...
  14. M

    Kent Petersen

    I finally mounted the #45 loader to my old 52 A. Thank you for this great piece of equipment.
  15. D

    Millermatic 210 feed failure

    About all I can find on the net is clean the drive motor and hope it kicks back on. Called Miller and tech said motor or board. Kinda got spoiled by the MIG and arc welder needs hooking up to finish a project. Gas comes on , solenoid ,and drive rollers jerk slightly but no feed of wire. ?
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top