(800) 853-2651
SHOP NOW

Recent content by keith1955

Yesterday's Tractor Forums
  1. K

    6 volt or 12 volt coil

    Thanks everyone. the coil turned out to be bad and it was a 12 volt.
  2. K

    Rear main seal

    I am having the same problem with my jubilee. I have torn this motor down twice and replaced the seals and still leaking lots of oil. I am really frustrated. I will try the rtf between the cap and block. Also I read instead of using the gaskets on the sides that are supposed to swell to use rtf...
  3. K

    6 volt or 12 volt coil

    Im getting a very weak spark on my jubilee. Im going to replace the coil but I'm not sure if it is 6 volt or 12. It has been converted to 12 volts but has a resister inline to the wire going to the coil. The coil on it has is a metal case and is a Motorcraft. Could this be the original 6 volt...
  4. K

    Rear seals on a Jubilee

    I just picked up rear seals for my Jubilee at a tractor supply. Mine had the rope seals in both slots. The dealer gave me rubber seals for all the slots , no rope seals. He said they will work. Has anyone used rubber seals completely ? If so which way do the lips go on each set ? Thanks
  5. K

    Rear seal on a jubilee

    I know this question has been asked before but heres the deal. The bearings were replaced in my jubilee last yr. My main rear seal is leaking now. Is there any way of getting out the old rope seal and replacing it with the rubber seal without tearing this thing apart ? Thanks for any replies
  6. K

    Oil pump

    I just purchased a new oil pump for my Jubilee . It came without a gasket so after reading another post here I assume I should use the Aviation gasket maker ? Can I get this at a Autozone or similar store ? Also should I put grease or anything in the pump to get it to prime better ? Thanks
  7. K

    oil pressure

    Thanks for the input. I have ordered a new oil pump and gauge and it came in today. Now I have more questions before I put this thing together again. The pump has no gasket between the body and plate. Do I need one ? Also do I need to put grease or anything inside the pump to get it to prime...
  8. K

    oil pressure

    I am ordering a gauge but I was trying to get it out of my garage. I hate to wait 10 days to get one. If I take the line off at the gauge would I get oil out of that line ?
  9. K

    oil pressure

    is there anyway of checking to be sure my oil pump is pumping on a jubilee ? My gauge is broken. Do these tractors have a sending unit to the gauge. Thanks
  10. K

    crank gear on jubilee

    Thanks guys. I used a puller and the gear came right off.
  11. K

    crank gear on jubilee

    Can anyone tell me if the crank gear on a jubilee is pressed on or just keyed? Any tips on getting it off ? I havent attempted it yet but have abad feeling . Thqanks
  12. K

    Oil pump removal

    I am replacing the bearings in my Jubilee. How does the oil pump come out. I have taken the nuts of the side and the but it doesn't want to come out. Do I need to remove the distributor first ? Thanks
  13. K

    starter switch

    I went to start my ford jubilee the other day and when I pushed the starter switch the starter began to crank as normal , but when I let off the switch it continued to crank. I had to unhook the ground post to get it to stop. Now when I connect the battery it cranks on its own . This tractor...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top