(800) 853-2651
SHOP NOW

Recent content by Kellyc

Yesterday's Tractor Forums
  1. K

    Eaton Power steering pump O ring size??

    Thanks guys!! I did order a seal kit from Steiner. I am going to find and order extras.
  2. K

    Eaton Power steering pump O ring size??

    I have seen it on a image posted for the Char- Lynn 544 parts list. It looks like it is part 736. It also looks like it gives the size. But when I zoom in enough to see the size. Its distorted too much. I have plenty of the right inside diameter O rings. But every one I try leaks. So the OD...
  3. K

    IH 966 battery question.

    Ok good to know. I sold the 966 so I could get some cabbage to fix up my 400. Keeping that one for life. Going to miss having a diesel though. Sitting two years and starts right up. Try that with a gasser.
  4. K

    IH 966 battery question.

    Cough cough cough... The 966 is running now. Smoked me out of the shed.
  5. K

    IH 966 battery question.

    One more question though. If I am going to put a battery charger on this.Does it matter what battery I hook it too. And I assume 12 volt setting?
  6. K

    IH 966 battery question.

    Hey Allan Thanks, I got to looking at the Cables and there was no way for them to go parallel any way. I have been around. Changed jobs and things like that. Had not been working on the tractors for a while. That will have to change here pretty soon. I have a 400 in need of a rebuild.
  7. K

    IH 966 battery question.

    Hey guys... Brain fart time. I took the batteries off this thing a couple years ago. Now I have two new batteries and cant remember how they hooked up. Option 1: Frame to neg on bat 1, poss bat 1 to neg on Bat 2, Pos on bat 2 to starter ect. Option 2: Frame to neg on bat 1 to neg on...
  8. K

    Need Pistons!

    Try these guys. Big yard. Gotvald Implement 275 Sage Rd, Hillman, MN 56338 (320) 355-2500 They may have a used set for you.
  9. K

    Using a fire wrench?

    I am taking the wheels off this one, I have robbed so many parts off of it. its a parts machine now. And putting them on this one. The rubber pretty much has rotten off and the old welded rims have given out.
  10. K

    Using a fire wrench?

    Thanks Randy, I was not quite sure. Its seemed like the clamp was a big Ol heat sink. I need my H running again. Snow is getting piled up and I need to move the piles. Snow plows are fine until you get all the spots full.
  11. K

    Using a fire wrench?

    I am going to swap out the wheels from 300 to my H. ( I assume they will fit) I busted one socket trying to loosen the bolts on the axle wedge. What do I want to heat up. The bolt or the wedge? I know stupid question but I have never done it before. Oh and do I wait until it has cooled...
  12. K

    My website is still up.

    Sort of..... I am missing some things but I had to move it to a free site. My Farmall site.
  13. K

    Where's our old freind kelly?

    I am still around. Just haven"t been doing much with my Tractors of late. I am spending time teaching my Son hunting, shooting and reloading. Found we share that interest. My shed still has the 966 in need of a piston pin, 300 is still in parts. Actually it in more parts because I rob them for...
  14. K

    Ford's Finest....

    "everyone said the coil packs do not go bad" They Lie dont they? I drove a 150 at work with those coil packs. In 3 years I had it in 4 times replacing coil packs. Although I had the last of our 4 wheel drives and they could get it from me after prying it from my cold dead hands. They kept trying...
  15. K

    560 sleeve explosion-million dollar question

    Oh also. If yours is a C263. I have some old sleeves and pistons you can have for the shipping cost.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top