(800) 853-2651
SHOP NOW

Recent content by Ken from Pa.

Yesterday's Tractor Forums
  1. K

    Axle center Pin Bushing

    I didn't do any miking when I installed mine But of course I got mine elsewhere .Is the bushing sloppy or the pin ? There's a guy named Don B over on the ntractor forum that could mike on of his for ya .Sorry I can't help ya more . God bless, Ken
  2. K

    ammeter 6 volt

    Someone on the ntractor board had a similar problem awhile back . I think he was adviced to check his wiring on the amp guage & the VR . I'm not knowledged enough to help other than say maybe you could go there & ask . Maybe he'll see your question & help you out .If I can be of any other help...
  3. K

    DEARBORN 3 point 2 bottom plow

    It depends on which model plow you have . All the ones I've been around from my childhood were painted Ford red . The extremely early models made for the 9n & Ford Fergusons were grey .HTH ! God bless, Ken
  4. K

    Dropping oil pan

    I hate to tell you this , but the front axle bolts to the oil pan . Be sure to support the tractor before attempting the axle removal . Block under the transmission as close to where the motor bolts to tranny as possible . It would be a good idea to have help when dealing with this project .You...
  5. K

    Keeping tools dry in winter

    I had a little different situation with my tools in the garage . Being that I'm getting older & sensitive fingers to cold steel & also trying to keep dust & dirt out of my boxes ; I had to do something . So I took a corner of the garage & built a small room with good insulation . I then...
  6. K

    10 Acres, an 8N and a disc...

    Now that sounds like it would've been an enjoyable project . I miss plowing , discing & harrowing the fields . Used to do alot of it as a kid . Its been about 50 yrs now . Those little Ns can surprise a guy huh ? Great part of history in hand . Njoy & God bless, Ken
  7. K

    Ford 600

    I have a 640 & I love it . It has all the power I need & some . I have a loader for it but never got it installed as of yet . I do wish it had PS though (somedayI hope) . I'm thinking its got 34 hp . Be sure to check it out good . If its in the right price range for you , get it . But always...
  8. K

    1953 NAA Will Not Start

    If it were mine after figureing out the problem ; replace the safety starter button & ignition switch . The way you discribe the gerry rigged wiring , someone could get seriously hurt by it getting started in gear .You have bought a well desired tractor , congratulations . Njoy & God bless, Ken
  9. K

    Adjust 8N regulator?

    Take your genny & regulator to an auto electrical repair shop & have them checked & set to work together . God bless, Ken
  10. K

    NAA not running right

    If I were you , I'd pull the big rubber vent hose from carb to aircleaner first . It maybe full of gas from float sticking . Then pull carb , either rebuild or check the float & replace & try it without the vent hose to see if gas runs out after it runs abit . If it does , you again have a...
  11. K

    Ford 801 Series Pinion Gear Needed

    Try [email protected] . He may have one . Mention my name . God bless, Ken
  12. K

    the economy and your area?

    Here in this small town of Franklin, the hospital , doctors , lawyers , cops & prisons & oh ya, the welfare employees jobs are booming . Factories are almost extinct . The banks & sherriff are having a hayday taking the poor folks homes away from them that can't work due to disabilities or just...
  13. K

    Changing a Read Tire (11.2 - 28)

    I tried removing the old tires from my wheels & decided for the 5o bucks its not worth all the havic it caused me . Not to mention the pinched fingers & a big bruise from when the tool slipped . You maybe further ahead to just order a new wheel, tire & tube all ready assembled from Tucker Tire...
  14. K

    tractor tragedy

    I sure hope nobody got hurt ? Machines can be replaced even though they're expensive . Do you have any info on the operator ? God bless, Ken
  15. K

    850 Ford front radiator guard

    It must be an aftermarket one . They will fit all those listed plus yours . God bless , Ken
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top