-
K
OT Stolen Valor
I was a squad leader in A Co 2nd Bn 327th Inf 101st Airborne in VIet Nam. I don't remember carrying a plastic spoon in my pocket. As a squad leader I was entrusted with a map of our AO and that I folded up to fit in a prc 25 battery bag. My extra smokes and wallet I carried in a "go-go" box...- Ken(WI)
- Post #1
- Forum: Ford 9N, 2N & 8N
-
K
39 9N engine sputters
Thanks for the advice. Hopefully I'll be able to try get this done on Tuesday and I'll let you know what happens.- Ken(WI)
- Post #1
- Forum: Ford 9N, 2N & 8N
-
K
39 9N engine sputters
I have a 39 9N with newly overhauled motor, new wiring harness, new generator and cut-out, rebuilt carb, new gas tank, new battery, new heavy duty ground strap, new radiator cap, new positive cable and more. The oil pressure is about 38, fresh oil and filter and new plugs with the proper gap...- Ken(WI)
- Thread
- Replies: 3
- Forum: Ford 9N, 2N & 8N
-
K
ignition problem on Case VAC
My 92 year old father has a late 40s VAC, 6v system, with a problem. He has burned out 3 coils. After the motor starts, with a new coil, it runs for only a couple of minutes before it cooks the new coil. Does anyone have an idea of what might be the cause of this?- Ken(WI)
- Thread
- Replies: 3
- Forum: Case & David Brown
-
K
9N axle housing gasket
Nearing completion of my 9N restoration project. I put fluids in the tractor over the weekend and discovered a pretty nasty leak around the rear axle housing's joint with the differential housing. I had it apart and replaced the gasket. I was a rather thin piece of material and I didn't...- Ken(WI)
- Thread
- Replies: 2
- Forum: Ford 9N, 2N & 8N
-
K
9N front wheel hub grease seal
I have an early 9N, serial number 1448. I also have the original service manual and owners manual. (That's nice because there's no mention of 2Ns or 8Ns in the books) No offense to the 2s and 8s. It just nice. My problem is that my tractor has some parts that are very different that the newer...- Ken(WI)
- Thread
- Replies: 2
- Forum: Ford 9N, 2N & 8N
-
K
3 or 4 ring pistons
So... do I want to rebuild with 3 or 4 ring pistons?- Ken(WI)
- Thread
- Replies: 1
- Forum: Ford 9N, 2N & 8N
-
K
3 or 4 ring pistons
So... do I want to rebuild with 3 or 4 ring pistons?- Ken(WI)
- Thread
- Replies: 0
- Forum: Ford 9N, 2N & 8N
-
K
9N motor rebuild
He's going to tell me which sleeves, bearing size, oil pump etc., then I will order the parts and probably have them shipped to him. He is known as a rock solid engine builder who builds stock car racing engines here in central Wisconsin. He said that if he bought the parts from his regular...- Ken(WI)
- Post #1
- Forum: Ford 9N, 2N & 8N
-
K
9N motor rebuild
I am going to have a guy completely overhaul the motor on my 9N... sleeves, cylinders, valves, oil pump, carb... everything. He says that I should buy the parts. My question for the panel is where should I buy them? I've heard some scary talk about what you can buy if you're not careful. I...- Ken(WI)
- Thread
- Replies: 6
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy