(800) 853-2651
SHOP NOW

Recent content by Ken11487

Yesterday's Tractor Forums
  1. K

    2130 chatter from front pump?

    Forgot to say that the stream went on for 1 to 2 min after the tractor was shut off. Maybe the tank at the front draining dos through the leak? Is this probably a rock shaft seal leak or a lift cyl leak, or a bit of both??
  2. K

    2130 chatter from front pump?

    Plugged in block heater for a few hours Sat. When I took the tractor outside the noise was back most of the time, stops when a hydraulic function is pressed. Warmed up for a half hour more and looked in the oil filler hole. I expected to see a high pressure spray but found a stream about what...
  3. K

    2130 chatter from front pump?

    I'll try the loader test tomorrow, have the brake pedals off now for stuck pivot pin. Supposed to be warmer so may get a better test with warm oil.
  4. K

    2130 chatter from front pump?

    Also, in the last test outside in cool weather the pump noise never showed up. Probably not enough work to get it hot enough The loader return is factory plumed to the filter housing, pressure is "T"ed under the right foot. Dealer installed new. Worked well for 35 of the last 39 yrs...
  5. K

    2130 chatter from front pump?

    Tractor at shop temperature 55deg and yanking the steering wheel back and forth "madly" the pressure drops to around 1500psi. The guage bounces in a range of 300psi all the time. Same with transmission in hi or lo. Ran for only 5 min inside. Took tractor outside (below freezing) let warm for 15...
  6. K

    2130 chatter from front pump?

    thanks guys, you are the best! The tractor has hi/lo left of steering wheel. loader valve is JD stock from new, 146 loader. Think it is the small pump. Has large indent in front of pump. Steering seems ok, when it cools off it works again for a while. I think I am just south of you...
  7. K

    2130 chatter from front pump?

    Have a 66 hp 2130 4000hr, bought new with dealer installed 146 loader. Dealer rebuilt/checked over front pump 5 yrs/200hrs ago. I have a metalic chattering noise from the area of the front pump. Seems to go away when a hyd function is used like the loader or the scv even with no load attached...
  8. K

    4240 No Left Brake,update, next step

    Why replace the spacer? Does it wear crooked and not hold the bearing well?
  9. K

    4240 No Left Brake,update, next step

    I see the new spacer measures 15 mm, my old one appears to be 12 mm. Will this make a difference if so? Maybe new stock old stock thing. Will this affect the bearing preload setup?
  10. K

    4240 No Left Brake,update, next step

    Make that .050' not.005' for the ridge in above post. Ken
  11. K

    4240 No Left Brake,update, next step

    Thx for the idea Tim, eyeing up my heavy bench right now. Meanwhile we are changing the seal on the axle. Do we have to remove the bearing to change the seal? How would we not damage the bearing. There seems to be a ridge about .005'to.010' higher than the seal seating surface, that the...
  12. K

    4240 No Left Brake,update, next step

    Matched my brake back plate # R60116 to use 2593R and R708R rivets and piston plates to D1761R rivets. Tested torquing up the special bolt, seemed like it was right, then removed axle from housing to refurbish seals. The outer seal was a bit brittle so felt it was time. I hope to just...
  13. K

    4240 No Left Brake,update, next step

    A&I says their fiber pads replace my originals. Just tried to measure end play with the axle housing hanging from the fork lift. Couldn't get any movement when tapping or lifting on the axle end. It must be fairly tight anyway. thinking of turning it by hand and tightening the bearings...
  14. K

    4240 No Left Brake,update, next step

    Aha, right again, Tim. Looks like the bleed valve was passing oil. I know we checked that last spring but I was the guy in the cab, not on the wrench. Anyway the leak is stopped, and the bearings and brakes need service. The brake pads measure .110' thick. How thick are new pads?Deere shows...
  15. K

    4240 No Left Brake,update, next step

    Also the axle shaft outer seal does not leak but the radial bearing play measured .003 to .004". Can I just tighten up the bearings to zero end play and have good radial play? I think the goal is .001" radial play? Ken
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top