(800) 853-2651
SHOP NOW

Recent content by Kendall W

Yesterday's Tractor Forums
  1. K

    I have a Makita 18v drill and the chuck is junk.

    The metabo chucks I have have a sharp edge that bites the bit and think they are angled slightly to bite harder if they tried to slip. I have a few bits with marks but no slip marks.
  2. K

    I have a Makita 18v drill and the chuck is junk.

    I buy Metabo keyless chucks and they work great for me. They seem to slip into a lower gear when tightening and have never slipped for me. Tighten as tight as possible and always loosen easily.
  3. K

    2N Manifold Stud Removal Help

    Thats right, I like to see color just for the fact it helps break the rust.
  4. K

    2N Manifold Stud Removal Help

    Heat it up as best as you can, preferably orange and as it cools use a candle and let the wax melt around the threads. let cool completely before trying to remove.
  5. K

    Is this 720 in neutral?

    Sounds to me it is stuck in 2 gears. Many years ago we had a 60 do that. If they are forced from one side of the quadrant to the other side without the belt pulley slowly turning that will happen. Wear over time and a quick shift will throw an extra gear in the mix. Pull the top off and get the...
  6. K

    Matador sprayer residue on corn

    I always used a little bleach to rinse my sprayer out. Never had a problem with Roundup to broadleaf only.
  7. K

    JD 60 PTO Shaft Coupler

    I just did my 630 a couple of months ago and just slide it on the front shaft first and then slide everything together. I used just black silicone and no gasket. put the silicone on and let that setup for an hour and slide it together and put all bolts in and snug it up lightly till I could see...
  8. K

    Snake oil, what to use.

    I have used Seafoam over the years and have had great luck with it. Can you work the engine and get it warmed up good? Maybe weld or generate power for a while. I remember years ago we had a little Honda engine that had sat for years, cleaned up the gas tank and new gas with some Seafoam in the...
  9. K

    JD 630 steering shaft removal

    Thanks, it was binding on the guide bolts. I got it fixed and all put back together.
  10. K

    Removing the hydraulic casting on JD 630.

    Got it back together except the pto, tomorrow for that. Thanks everyone for the help!:D
  11. K

    Removing the hydraulic casting on JD 630.

    That did it! Thanks:D
  12. K

    Removing the hydraulic casting on JD 630.

    Yes I have it hanging on a picker and I will try removing the guide bolts. Thanks
  13. K

    Removing the hydraulic casting on JD 630.

    Yes it is the rockshaft housing i,m trying to remove. I can see the seal just hanging on the pto driven shaft. I did engage the pto clutch before removing it. All lines and linkage are disconnected.
  14. K

    Removing the hydraulic casting on JD 630.

    Yes i,m trying to remove the hyd housing that holds the pto clutch so I can replace the oil seal to the pto.
  15. K

    Removing the hydraulic casting on JD 630.

    I,m trying to remove the hydraulic casting on the back of the JD 630 and it comes off about 3 1/2 " and doesn't come any farther. I have 8" long guide bolts in the two top holes and seems I can wiggle it but does not come off. Needing to replace the seal to the pto as I can see it is just...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top