(800) 853-2651
SHOP NOW

Recent content by KennyDiesel

Yesterday's Tractor Forums
  1. K

    Hose crimper Dayco

    I have a dayco np-60 crimper, 3 wires that control travel got knocked off. Can anyone tell me the connector terminals hookup.
  2. K

    G JD

    Can move into 5 gear. Is one of these plug the detent?
  3. K

    G jJD timing

    Drove G JD down road today and came back and would run on , after turning key off. I had counted teeth on flywheel and like 22 teeth should be around 26 degrees timing . Set this mark at WOT and at idle it came real close to mark for idle. If I set distributor by points opening , to...
  4. K

    Backrest A JD

    Looking for back seat of A sn 593386. First set of holes outside is 1 1/4. Second set is 1 1/16 ....
  5. K

    G John Deere oil pressure

    Will try tomorrow and let run, thanks for info on seal. That important to. If I remember some on the Perkins diesel ran around 10 psi. They said pressure did not matter ,just had to have oil there.
  6. K

    G John Deere oil pressure

    Removed starter and plate. Turn screw two turns, same oil, went from 10 to 18 psi at idle .. 11 wide open to 20 psi ,, this is cold engine, 10-30 oil
  7. K

    G John Deere oil pressure

    I think a 42. Sn 53672
  8. K

    G John Deere oil pressure

    I might be posting this twice, but what is the oil pressure you guys have.?
  9. K

    G John Deere oil pressure

    What are you running for pressure?
  10. K

    A John Deere piston

    Has the groves for sparkplug down
  11. K

    G John Deere oil pressure

    If it has 10 psi at 800 rpm and only 11 psi at wide open , do you think adjusting relief valve will help? Has 10-30 oil ,new filter
  12. K

    A John Deere piston

    Removed cracked head and number 2 piston in turned 180 off. Remove rod cover and number on rod is up. Would you remove or it been this way for years and leave alone.
  13. K

    G JD clutch

    The book talks about removing .030 from the clutch sleeve ,if having problems getting clutch to work. But it does not tell what the original spec is, so dont know if someone already did this. Does anyone have this length, later model G.
  14. K

    G John deere

    Its says to soak head gasket in engine oil before installing, is this correct. I have block and frame removed , can I install block and head and then install frame, there is bolts going from frame to block?
  15. K

    D17

    Neighbor gave me a D17 with motor stuck. He also has a c gleaner that has been sitting for 10 years put can turn motor over, will it fit in D17. I own a WD, but would like wide front, if above will not work can I put wd into d17
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top