-
K
Oil Capacities
Here are photos from the Ford manual that I followed looking for differential oil capacities. the # 3 in ( ) through me off.- kensikora
- Post #9
- Forum: Tractor & Farm Talk
-
K
Oil Capacities
Yes, the differential is what I am asking about. 11-1/2 qts. makes more sense than what I see in my book. Rather than the (3) in ( ). Thank you for the replies.- kensikora
- Post #7
- Forum: Tractor & Farm Talk
-
K
Oil Capacities
In the Ford 861 tractor manual, under capacities, differential oil quarts for some models are the #8. But for the 800 series, it shows a (3). Why the ( )? Is that the number of quarts in the ( )? --- which is only listed as 3? Is it only 3 for such a big tractor? K.S.- kensikora
- Thread
- Replies: 9
- Forum: Tractor & Farm Talk
-
K
1958 Ford Hydraulic lift problems
In one of your pictures, you have your letter "T" and above the T is a pin sticking up. I had an accident and broke the pin off. So I bonded the pin back in and I do not know exactly what the pin does. Hopefully, that will work??? When I hold the draft control lever down and work the... -
K
1958 Ford Hydraulic lift problems
Picture is taken straight forward. Shall I take another? -
K
Ford 861 3 pt. hydraulic problem
n the picture, the linkage connections are outside of the lid opening. I assume that it should be bent to the left? Hopefully the parts are not cast iron and liable to break(???) Please reply as soon as possible?- kensikora
- Post #22
- Forum: Restoration Processes
-
K
1958 Ford Hydraulic lift problems
In the picture, the linkage connections are outside of the lid opening. I assume that it should be bent to the left? Hopefully the parts are not cast iron and liable to break(???) Please reply as soon as possible? -
K
Ford 861 3 pt. hydraulic problem
Ford 861 Hydraulic lift problems: 1. With everything back together and the tractor running; I tried moving the linkages withy a heavy, long screwdriver thru the hydraulic oil fill opening, but nothing worked for me (?) 2.With the tractor running, I worked the selector lever, on the right...- kensikora
- Post #21
- Forum: Restoration Processes
-
K
1958 Ford Hydraulic lift problems
Ford 861 Hydraulic lift problems: 1. With everything back together and the tractor running; I tried moving the linkages withy a heavy, long screwdriver thru the hydraulic oil fill opening, but nothing worked for me (?) 2.With the tractor running, I worked the selector lever, on the right... -
K
1958 Ford Hydraulic lift problems
One other thing, I noticed that the piston never leaves the far end of the cylinder. Today I am trying the screwdriver through the fill hole to move the linkage to see what happens. Any other ideas for me? -
K
Ford 861 3 pt. hydraulic problem
I just did that, . . . I think. (I am new to this post.) Thanks. Let's see if anyone answers?- kensikora
- Post #20
- Forum: Restoration Processes
-
K
1958 Ford Hydraulic lift problems
I have a 1958 Ford 861. The hydraulic arms will not lift. What can my problem be? 1. Cam pin is o.k. 2. Cylinder wall very smooth. 3. Side control lever does not help. 4. Oil pushing out of the top of the pump - Not sure of the pressure. 5. Hydraulic sump oil has been... -
K
Ford 861 3 pt. hydraulic problem
1. A year ago this past Fall, the top cover was removed and fixed. Then, come Spring, it stopped working again. 2. Yes. I have pressure at the pump. 3. The draft lever moves, with no response. 4. Yes, I replaced it with hydraulic/trans oil. Drained the system already. 5. I do not...- kensikora
- Post #17
- Forum: Restoration Processes
-
K
Ford 861 rear axle fluid
Steve, Could you go back a week or so and see my posts about a 1958 Ford 3 point hitch hydraulic lift problem? Trying to get the arms to lift, but can't. Tried others suggestions, but nothing is working yet. Ken- kensikora
- Post #4
- Forum: Restoration Processes
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy