(800) 853-2651
SHOP NOW

Recent content by kip78

Yesterday's Tractor Forums
  1. K

    Some aluminum welding glitz....

    I don't know how big that plate is, but when we make fixtures for vibe testing, we try to make them from one piece of billet.
  2. K

    OT: There are alternatives to burning wood.

    I'm not anti burning, I just don't want to smell your smoke. I'm not anti neighbor, I just don't want to live next to people like you. You seem to think everyone is flush with cash like you.
  3. K

    TO35 clutch help

    When I did my dual clutch I took the flywheel off and adjusted it on the table. Was having problems with alignment on the engine and the clutch disk wanted to get pinched between the flywheel and pressure plate. Can the disc go on backwards? Been some years since I changed mine.
  4. K

    TO35 clutch help

    Aren't the pto screws supposed to be set at .09?
  5. K

    MCCA rebate

    Gretchen had plenty of input, she has the veto pen and uses it plenty. The problem with Detroit is the people of Detroit. Why is insurance so much more there? It comes down to behavior. Putting two thirds of the state in the same category as everyone else isn't right. Up until not to long ago...
  6. K

    MCCA rebate

    So what you're saying is people shouldn't have a choice. The problem with the law change is it wasn't a clean break. Governor lath and plaster wanted insurance premiums to be rated equally regardless of where you live. Therefore, run down dumps like Detroit where half of the drivers that have no...
  7. K

    MCCA rebate

    The entire thing was concocted by lobbying back in the 70's. It was baked into insurance premiums with no way to drop it. Until the law changed, you couldn't even get a court to show how much was in the fund or what was spent every year. Zero transparency. If this law was so good, why was...
  8. K

    MCCA rebate

    Who cares, at least now people have a choice.
  9. K

    Cylinder sleeve O-Rings- replace if not pulling sleeves?

    Pull the sleeves and change o-rings. Did my to35 and found enough stop leak in it that cylinders 3 and 4 were getting no coolant to them.
  10. K

    Home town case history

    Had a 411b-h that had com
  11. K

    Cub Cader

    Does it have a wire to the bowl? The electric solenoids like to stick on those Kohler motors.
  12. K

    Testing_electric tractor

    John Deere has r and d facility in Manheim.
  13. K

    world going nuts!

    Not that copper is heavy but expensive.
  14. K

    world going nuts!

    You think the old timers could do the same considering the government requirements today?
  15. K

    Shop Time: Diesel Edition

    I thought head gasket issues were only with LB7 engines. Those balance rates are incredible. I had aLB7 and after 300k miles I dumped it after it had the first injector recall, then two others and two sets of head gaskets. Also plastic water pump impeller issue, and the np transfer case problem...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top