Recent content by Kirk McDaniel

  1. K

    Ford 6700 clutch

    A couple of weeks ago we replaced the clutch, throwout bearing, pilot bearing and had the pressure plate tested and springs replaced as needed. The 2 guys that work for me have replaeced cluthes a number of times on various Ford tractors I having including this one. Never a problem. This time...
  2. K

    HYDRAULIC LIFT ON A FORD 4000

    Honestly, I'm not sure what part that is but if it is the piston like value with a large o-ring it does move freely with no problem. I'll look at a diagram to see what part is the unloader valve to make sure we checked it.
  3. K

    HYDRAULIC LIFT ON A FORD 4000

    The hydraulic lift on my 4000 is stuck in the up position and i can"t figure out what the problem is. I have pulled the top off the rearend and replaced all the o-rings and the o-ring and gasket on the piston but it still wants to rise up regardless of the postion of the control level. It will...
  4. K

    4610 with water in the oil

    I have a ford 4610 that has water in the oil. I took the head off, had it checked and ground and put on a new head gasket. Still getting water in oil. I cracked it up and filled the radiator with about 1gal. of water and within 15 to 20 minutes I couldn"t see any water when I looked in the...
  5. K

    6700 hydraulic pump

    Thanks to all of you for your advice. If I knew how to keep the coffeee hot, I would send you guys a cup. Kirk
  6. K

    Ford 6700

    I failed to mention I had changed the filter and all hydraulic fluid right after the problem manifested itself. I've only changed the filter once when i changed the fluid.
  7. K

    Ford 6700

    A couple of months ago I wrote to ask about a problem I was having with the PTO on my 6700. It would not run my round baler. After replacing the PTO clutch, twice, it started working fine. (The second time i just rebuilt the original clutch after putting in a used one). The baler ran fine for a...
  8. K

    Same old, Same old. 6700 Ford PTO

    RodInNS , you were right. We found the leak and it was in the clutch pack that we put in. We've had that transmission out so many times I've asked the mechanic to put a zipper in it to save time turning bolts. Thanks for everyone's help. Now I'm taking my problem up with the company that sold...
  9. K

    Same old, Same old. 6700 Ford PTO

    Without belaboring previous inquiries, I had to replace the pto clutch pack (rebuilt not new)because the previous one was damaged when the transmission was put back in. The PTO quit turning after one of my guys baled 2 round bales. When I cranked the 6700 Saturday and engaged the PTO, it started...
  10. K

    Ford PTO clutch pack

    Dave, I hate to sound so blasted ignorant but I have never worked on the PTO or ever had a problem with any. I've been operating tractors for 45 years but we have a cattle opeartion and it's pretty much get on and go. Hook up a baler, mower, box blade or rake and we've done about all we're going...
  11. K

    Ford PTO clutch pack

    I wrote a couple of weeks ago and got great advice on what was the cause of the PTO failure in my Ford 6700. of course the mechanic denied any involvement but i felt better knowing what really happened. We got the new (rebuilt) clutch pack installed and the PTO seemed to work fine until we began...
  12. K

    Ford 6700 with frozen PTO

    Thanks for everyone"s help.
  13. K

    Ford 6700 with frozen PTO

    I recently had to replace a shift fork in my transmission on a 6700. This required the entire transmission to be torn down. While in there, I replaced the clutch, pressure plate, etc. Got it back together and it ran fine but never used the pto. This spring, we hooked the baler to it and the pto...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top