(800) 853-2651
SHOP NOW

Recent content by Kondoge

Yesterday's Tractor Forums
  1. Kondoge

    Mini ALT for 9n or no? Apology.... and the results of it all

    n like I said guilt eats at me if I didn’t say nothing I’d have felt like crap
  2. Kondoge

    Mini ALT for 9n or no? Apology.... and the results of it all

    Which volt meter should I put that looks kinda matching to the stock oil pressure gauge
  3. Kondoge

    Is it possible to switch a side mount 8N block to a front mount setup?

    on the plus side your engine will have a unique story to share of how it came to be.
  4. Kondoge

    Mini ALT for 9n or no? Apology.... and the results of it all

    Figured this had to go on the same board as the thread it all started on, wouldn't feel right to put it somewheres else. I know that thread "Mini alternator for 9N or no?" a while back may have upset quite a few on this board , that was a BIG oopsie from me. I take the fault for that one. If I...
  5. Kondoge

    Is it possible to switch a side mount 8N block to a front mount setup?

    mine has an 8n engine that's why I was asking might be a worthwhile investment no?.... probably not.... Steveh1155 some redneck ingenuity outta carry you through, no duct tape and baling wire though you must promise us that.
  6. Kondoge

    Is it possible to switch a side mount 8N block to a front mount setup?

    Nevermind about my nonsense actually you can it just takes some custom fabrication but I say all the power to ya. if you can tell us how it works out and what you had to do, almost makes me wonder now if the inverse is possible, A side mount installed to a front mount block. A quick Google does...
  7. Kondoge

    Is it possible to switch a side mount 8N block to a front mount setup?

    Hobo I thought you were a goner man haven't seen you post in a while, also what? you mean a person could have a sidemount 8N block with a front dizzy on? I thought that wouldn't work but I haven't owned an 8N side mount either all I have to go off of is my own experience with the blocks I have seen.
  8. Kondoge

    Is it possible to switch a side mount 8N block to a front mount setup?

    I'm sorry to burst your bubble but I'm just gonna straight up say it, its way too much time, money, and effort to swap it, you would be better off just getting the missing parts. or you could try to have somebody fix the crack in your old front mount block, depending on how bad it is and where...
  9. Kondoge

    Buster the 9N a possible rarity?

    I suppose the zinc oxide primer makes that color too, :(, a case of thinking my tractor again is above average
  10. Kondoge

    Buster the 9N a possible rarity?

    Thats actually cool, he should make it the 5 different colors in sections from front to back.
  11. Kondoge

    Buster the 9N a possible rarity?

    On buster specifically he’s Been the gray he’s been maintenance green, blue with orange stripes then a red belly, then straight white with red rims. The front reds I hear are official ford new old stocks that were left in the red primer instead of painted.
  12. Kondoge

    Buster the 9N a possible rarity?

    I have reasonable suspicion here. so I noticed when scraping the dash above the factory gray paint layer was a mintish light green, upon looking into the color said green is apparently typical of some of the historical Alberta maintenance teams (I cant say if this is true I wasn't alive in 1940)...
  13. Kondoge

    What's the purpose?

    they work great if you use them right and set them up right, that and you have brakes to use, for me I find you will know if their toothed bits are installed wrong because when you push the pedal down it will latch and the pedal will get stuck down. Or could it be my old 9N mutt pleading with me...
  14. Kondoge

    Ford 9N Governor Lubrication

    I vote redneck repair as the cause.
  15. Kondoge

    Installing a turbocharger on a 9 n ford

    Can confirm Harry, I’ve been there and have a mindset of it starts it runs it’s working, the valves make tapping sounds and it sometimes tries to stall when I back off throttle but because it works I see no need to mess with things, if it ain’t broke don’t fix it, a phrase that contributes to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top