(800) 853-2651
SHOP NOW

Recent content by Larry Condon

Yesterday's Tractor Forums
  1. L

    What do you all thing of the spring wheat prices??

    Like they say if your in the stock market; be diversified!!
  2. L

    Sleeve O ring lube

    Liquid dish soap
  3. L

    Exhaust ports on WD45 Head

    I have a 56 International truck that the exhaust manifold was leaking at one port after installing a new gasket. I mixed up some JB Weld and packed it in and it has held great. Larry
  4. L

    Piston pins, what kind of steel?

    You have to machine the tool steel in the soft state and have the steel heat treated or harden to the specifications of the type of tool steel used.
  5. L

    Farmall C clutch

    You must be referring to the throw out fingers. I had the same problem with a F20 clutch. Be careful with just trying to drill out the holes larger. If worn oblong the drill will wander out of concentricity and you will have a hole that is not round and out of location. I fixed mine by setting...
  6. L

    F12/F14 Universal Joint Bolts

    When I re-built my F20 clutch and spline drive clutch shaft I made my own joint bolts and the joint plate that connected the universal. I purchased new rubber washers from Rice Equipment. I have a lathe and mill in my shop. Larry
  7. L

    Took Micrometer Apart

    Most mics come from the factory +/- .0002-.0003 setting. You can hold them in your hand for a few minutes and body temp will change that tolerance. Larry
  8. L

    F-12 crank shaft knuckel

    Can you post a picture so I can see what it looks like. Thanks
  9. L

    wd45 motor froze need help

    Even if you are successful in removing the stuck pistons, you should pull the sleeves and replace the o-rings around the sleeves. I believe they are wet sleeves. The o-rings maybe in bad shape and leak anti-freeze into the oil pan after you re-assemble the engine. The o-rings are not expensive.
  10. L

    Loose Sleeve

    Make sure that the head is holding the sleeve down tight. When the sleeve is installed measure how high it sets above the block, should be at least .003-.004 above. Larry
  11. L

    OT- Who remembers Moto-ski snowmobiles?

    Owned a 1974 Motoski 292 cc. Drove it till it fell apart.
  12. L

    F-20 brake levers 1 or 2

    My 1937 F20 has two brake levers and the left side is longer than the right side.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top