(800) 853-2651
SHOP NOW

Recent content by lavallj3

Yesterday's Tractor Forums
  1. L

    1010 wiring schematic

    Gas
  2. L

    1010 wiring schematic

    Does anyone have a wiring schematic for a John Deere 1010, SN 15001RU?
  3. L

    John Deere 1010 will not run properly

    It is a replacement carb that is suppose to out perform the original. I will try and open it up some more.
  4. L

    John Deere 1010 will not run properly

    Plugs, wires, points, and condensor are new. I took the distributor apart and the advance does move but it is dirty. My next step was clean and lubricate the advance. The timing was set at 2500 rpm because that is what the IT shop manual says to set it at (not sure that it is right, but that...
  5. L

    John Deere 1010 will not run properly

    I have a 1960 John Deere 1010 (Gas) that starts hard and when I try to rev it up it sputters and dies unless I ease on the throttle. I just rebuilt the engine and put a new Zenith carb on it and adjusted the jets 1 1/2 to 2 turns out. When I timed it with the light (@2500rpm) I did notice the...
  6. L

    What is this loader? Was on a Cub.

    I do not think it is a henderson, it does not appear to look the same as a henderson. If you google "farmall cub loader" and go under images at the top of the page there is a cub with silver wheel weights that has the same loader as the one I have. The pic is not good enough to see exactly how...
  7. L

    What is this loader? Was on a Cub.

    The tractor was purchased without the loader attached and my friend never went back to get the brackets to mount it, but is was on this cub at one time.
  8. L

    What is this loader? Was on a Cub.

    I have this loader that was on a farmall cub I am restoring for a friend but there are are no mounting brackets and I can't find any info on it. Does anyone know what brand loader this is and how it mounts on a cub?
  9. L

    1948 Farmall Cub Loader

    Does anyone have a 48 farmall cub with a loader? I have one but it is missing the mounting brackets and I need pics to see what they look like so I can make some and see how it mounts to the tractor. Thanks
  10. L

    H card leaking

    Yes all the gaskets are new and everything seems to be moving freely when I take it apart. If I turn the fuel on (when it is apart) I can lightly lift on the float and the needle will seat and shut the fuel off. I will have to pull it apart again and look it over again.
  11. L

    H card leaking

    When I take it apart the float moves up and down freely with no issues.
  12. L

    H card leaking

    I can not see where it is rubbing. I have pulled this thing apart at least 20 times and I see no sign of rubbing and it does not appear to be crooked. I am pulling my hair out on this one.
  13. L

    H card leaking

    I can not see where it is rubbing. I have pulled this thing apart at least 20 times and I see no sign of rubbing and it does not appear to be crooked. I am pulling my hair out on this one.
  14. L

    H card leaking

    I have a farmall H I just rebuilt the carb in and it wont stop leaking gas when I shut the tractor off. When I rebuilt the carb the needle, seat and float were replaced and the float does not appear to be catching the sides of the bowl. 90% of the time after I shut the tractor off the gas...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top