(800) 853-2651
SHOP NOW

Recent content by lemroy

Yesterday's Tractor Forums
  1. L

    Burning question for the evening?

    When I was a youngster(I am now 88) in SE Ok the cafes served coffee with saucers, You could pour the coffee in the saucer and wait for it to cool.
  2. L

    Gas in diesel tractor

    I accidentally filled my Dodge diesel pu with gas. It ran ok for about 5 blocks and then started smoking, I drained the gas out and put diesel in it. It is running great now. Roy
  3. L

    JD 4430 turning problem

    Thanks I will try this. Roy
  4. L

    Night crawlers and walnuts

    My fatherinlaw use green walnuts to catch fish. He would go to the mouth of a stream with a sack of green walnuts and beat them until the sap began to come out and the fish would come to the top to be scooped up with a net. I don't know if this is legal. Roy
  5. L

    JD 4430 turning problem

    I WAS TOLD BY A JD mech that this could be taken care of by adjusting the linkage. i will try this. Thanks all you techs. Roy
  6. L

    JD 4430 turning problem

    I have had this tractor about 20 years and it has always had this problem. Roy
  7. L

    JD 4430 turning problem

    On my 4430 it will turn real short to the right, however it doesn't turn short to the left. How do you correct this. Roy
  8. L

    Clutch Disc for an HD11-E

    You might try gemdozer. He has a lot of spare parts for Allis mAchines. Roy
  9. L

    JD 4430 injector line problem

    Thanks all you techs. I will see if our local JD dealer can get these. Roy
  10. L

    JD 4430 injector line problem

    Where can I order that type setup for a JD 4430? Thanks. ROY
  11. L

    JD 4430 injector line problem

    I have trouble with the rubber tees that connect fuel line to injectors. Is there an after mkt syst em to replace these tees. Roy
  12. L

    4430 JD hydraulic problems

    JD wanted $2700 for a new pump. I ordered a reman from Abilene Mach for $1100. It works just fine. Roy
  13. L

    4430 JD hydraulic problems

    I got the tractor out of the shop. It cost $5400 bit it works fine. I prolly got took. Roy
  14. L

    stripped threads on a bushog bolt

    I welded the nut on the bottom of the brushhog. I don't know how long that will last. However the cutter is getting old. I will prolly have to get another one. Thanks all you techs. Roy
  15. L

    stripped threads on a bushog bolt

    On my six foot Bushog the bolt that holds the stumpjumper and blades is stripped. How do I change it out or do I need to buy a new gearbox. Roy
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top