(800) 853-2651
SHOP NOW

Recent content by lowline_farmer

Yesterday's Tractor Forums
  1. L

    Ford 3000 carburetor problems

    The problem is somebody took the fuel pump off all the lines and fuel pushrod and now they can't find them
  2. L

    Ford 3000 carburetor problems

    what model of Zenith carburetor do I need ? Are those aftermarket carburetor on E-BAY any good
  3. L

    Ford 3000 carburetor problems

    Its a Holley carburetor . I was going to rebuild the carburetor but it didn't look right with the needle mixture screw sticking out .
  4. L

    Ford 3000 carburetor problems

    I inherited a Ford 3000 tractor I'm looking for some help having carburetor trouble on the manifold side idle mixture screw does it go into the throat because I an see the idle mixture screw tip on the inside of throat when its all the way screwed in also does any body out there have any used...
  5. L

    loader instalation

    this is the only numbers I have on the casting valve so what size spool valve do I need for my ford 5000 only pumps 6 gpm how big of a spool valve do I need
  6. L

    loader instalation

    DO I need to buy a new valve then
  7. L

    loader instalation

    I don't know I bought it at an auction sale
  8. L

    loader instalation

    I have a dual 205 loader it came off a ford 6600 I am installing it on a 1976 ford 5000 I need help pluming it I have a small 1/4 inch hose on the control valve I need to know what it is used for do I need it if I need it where do I plum it in at on the tractor or can I just plug it here are...
  9. L

    ford 800

    do you know where I can buy it and thank you very much for your help
  10. L

    ford 800

    thanks all of the people who gave me information on my problem with my ford 800 hydraulic pump. I fixed the problem. I bought some parts from reliable aftermarket parts and the valve plate was the wrong size of roll pins on the plate which held the valves open. I would like to know what is the...
  11. L

    ford 800

    no it is run off of the on board hydraulics what type of fluid does it take I put in M2C41 got it at farm&fleet will the fluid make a difference.
  12. L

    ford 800

    I have a ford 800 tractor hydraulics worked good but had a gasket leak in the pump. the loader worked fine before I took the pump off. I replaced the gasket. now I can't get it to prime. what do I do to fix this issue? I tried to bleed the air out but it didn't work. thanks lowline_farmer
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top