(800) 853-2651
SHOP NOW

Recent content by lyric

Yesterday's Tractor Forums
  1. M

    Think before you torch

    I was needing to pull the gearbox on my rhino brush hog. The box was bolted through the deck with six 3/4" bolts. Normally, I would have fought with wrenching them off for a couple of hours, bracing a wrench below. Then I would climb out and try to turn the nut from above. Then the bottom wrench...
  2. L

    front wheel weights?

    Are you sure the last letter is an A? If its actually R 226R then its for an 80,830,840 70D,720D,730D & R. I looked the #'s up in the master parts index, but never found R 226A. Hope this helps. Kevin
  3. L

    Lead washers?

    I was assuming that's what they were for, in case water got past the gasket some how. Gaurling makes sence when Tim posted it. I understand small diameter washers were unavalible at the time. Thanks for correcting me on this. Kevin
  4. L

    Lead washers?

    Most of the engine rebuild gasket kits come with them, if not you can get the at the JD dealer. They come in a box of 50, I just picked some up a couple weeks ago, think is about a dollar fifty a piece. They seal things up around the studs, my thoughts would be they belong there or they...
  5. L

    transporting a skeleton wheel B

    Belting seems to be the way to go, I work on a rock crushing plant, that would be the best place to find the belt cheap. We always have a roll or 2 of used belting around here looking for a new home. Works good in front of your work bench also, easier on the knees & feet at the end of the day. I...
  6. L

    530 valve adjuster

    Would anyone have the adjuster bolt for the valves? Screws into rocker & pushes against the push rods. Thanks, Kevin
  7. L

    JD B weight

    Well I'm not much help on the weights, but the 10,000 should be close. I bought 2 misfits in Duluth Mn. A couple years back & hauled them home with my 1500HD 6.0 liter & a tri axle fith wheel. I put the '40 on the front & '49 on the back, both have cast rear centers, not sure if they are loaded...
  8. L

    52 B, starting restoration

    Personaly I like JDfans approch. I bought a stuck '49 B, pulled the block & pressed out the pistons. I was lucky & only had to hone it & replaced the rings. Cant say that it cost a lot of money. I used the press at work, wasn't a bad push. Did the same to an R I bought sight unseen, that...
  9. L

    need parts for 1928 D

    I would have to check the serial numbers, think its a 1930 I have. Its stuck, but block looks good other than will need to be bored, think the head is good aswell. I'm only going to make it into a lawn ornament. If you care to look at it I'm on St.Joes Island Ontario, parts may work for you...
  10. L

    '38 with anti-freeze getting in the cylinders

    I was going to use water only because I have the water valve for it. I found it in the bottom of the tool box a couple years ago. I want to put it on, may never use it, but have it hooked up just the same. I plan to run the D for the rest of the summer the way it is, hopefully have the time in...
  11. L

    '38 with anti-freeze getting in the cylinders

    When I was getting the D re*dy for our July 1st parade, I noticed the white smoke & sweet smell of anti-freeze. I have since drained it & replaced with water, thinking I should try to flush out the antifreeze best I can. I will be only use water in it after repaired anyways. I was thinkigs...
  12. L

    '36 A oil pressure problems

    Problem solved, cranked down the adjuster screw more. Thought I had it tightened rather good, but got what we needed out of it. Thanks, Kevin
  13. L

    '36 A governor

    Thanks Mark, I tried downloading the link Bob listed, can't get it to work on the cell, I will try on desk top another day. We have a tractor parade here July 1, so time to make sure there all good to go. Thanks again guys, I like this forum, lots of knowledgeable guys interested it the same...
  14. L

    80 water pump belt

    Thanks Bob, I appreciate that. Kevin
  15. L

    What size tire is needed?

    I looked at dads '41B tonight, looks like the inside would be closer to 7 1/2" or 8" on his. He has 9 bolts steel rims on it with 11.2 x 38s. I also looked at my '40B with cast centres they look like 7". It has 10 x 38 on it. Tires are on so we couldn't get a true measurement. Hope this helps, Kevin
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top