-
M
Hook magizine
Brian, my son and I have not received ours yet ,central Illinois.- M 5 Jack
- Post #1
- Forum: Tractor Pulling
-
M
Tunica Photos
Brian, no problems here just hoping to be in your pictures or magazine like most people ,I got some things coming from K & L, I tried to say hi at your station but you were always busy, the price if success. We had a great time on our first pull there and had good results.- M 5 Jack
- Post #1
- Forum: Tractor Pulling
-
M
Tunica 2013
We signed Saturday morning ,our number was 415, we were weighed ,drawbar measured and we pulled ,no bs when we asked a question mean green people were helpfull . We had a great time.- M 5 Jack
- Post #1
- Forum: Tractor Pulling
-
M
Tunica Photos
Brian since I did not see my tractor I guess that i am going to have go with brand x magazine.- M 5 Jack
- Post #1
- Forum: Tractor Pulling
-
M
ub special
If anyone is in need of a UB Special hood I have a nice center piece,I do not have the side pieces. Located central Ill.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
L.P. tank
Hey Toolz, we are looking for flotation tires here on line. Can you get over creek turned river at Farmer City? We wanted to give ZB a test run #5 but govenor still acting up. I will be there if all possible,if for nothing else but to aggravate you and Dickie and his brand X tractors.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
L.P. tank
Hey Toolz, sometimes I think these Minnie"s are female, just a little hard to figure out. Did you get a front axle bushing yet.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
G704 on the dyno
The ground was wet plus Illinois muck. Plow was a 4/16 4440 oliver that somehow wound up mm brown with praire gold wheels and coulters. She was in third gear around 6.5 mph since 2nd gear needed replaced. The hidden tractor was a 720 JD with pump turned way up.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
G704 on the dyno
Our Gvi with advanced pump timing and pump work pulled 116 after overhaul , it has a 3 core radiator to keep cool.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
Gvi front axle pivot bushing
Hey tools Rob Ohda got me one for M5. We had one made for Gvi at Heritage welding for G vi .I have the new one for M5 standard in shop if yours is clear gone and need measurements . My computer has been down or I would have been back to you sooner.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
-
M
MM plow colors
Just for references I used IH red with the Prairie Gold for brown belly M 5's on wheels for our MM pipe plow. Plow was sandblased and a gray primer was used.- M 5 Jack
- Post #1
- Forum: Minneapolis-Moline
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy