(800) 853-2651
SHOP NOW

Recent content by M-Mfan55

Yesterday's Tractor Forums
  1. M

    electronic ignition

    If there is a tag on the sensor unit; take it off. At times they will not run. Also; be sure you have the proper coil. There are different coils for 4 or 6 cyl. and; as previously suggested; check the manufctures data.
  2. M

    Looking for a complete running 403

    I have a running 403 in a GB tractor. The tractor is a bit rough; engine sounds good with a set of 4210 heads. I am in Ky. May be too far away but if not you can call 270-925-5259 for price and details. Thanks
  3. M

    Osco 65

    I own an Osco 65 that was purchased new by my grandfather in 1949. Does anyone have any history or historic details on this garden tractor? I know it was built in Pa. (according to the tag) I also have an antique tractor book that shows it being built in '48 but no other years. ( it is built...
  4. M

    hitch measurement question. opinions please.

    Do not know where you are from; but; all the clubs and organizations in this area measure from the ground to the top of the hitch point. In our case; to the top of the pull ring where the sled hook goes. We do not usually pull from a clevis; but a stationary; fixed drawbar. we have been...
  5. M

    dry carb solved

    I posted on here a while back about a Stromberg carb that would not let gas into the bowl. I had guessed a float problem about the time I started getting replies. I just got time to take it back off; pull it apart; applied grease to the inside of the bowl; and; YES---- the float came back out...
  6. M

    build a pulling U

    What you can do depends on your bank account. It is possible to go near 700ci using stock jugs ; but requires a lot of machine shop work and "custom" built parts to get it to fit in the stock appearing engine. getting 400 plus inches the easiest is: 403 crank offset ground to 283 rod---custom...
  7. M

    looking for a built u puller motor

    I have a 618ci U that I will sell entire tractor for 6500
  8. M

    dry carb

    I have checked all that. I can see when I put it back together that the float and needle is down. I also have a 9psi pump in line. I have never encountered something like this
  9. M

    dry carb

    Has anyone ever experienced a carb that will not allow fuel to enter thru the inlet valve? I have a Stromberg that I can blow thru the line with the bowl off; but; when I put it back together; I cannot blow thru it. the vent to the bowl is clear. any ideas?????????
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top